You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
ADC INPUT with 4.10 HW running with 5.02 FW by mouadh on Tue, 2022-03-22 15:32 |
by mouadh Tue, 2022-03-22 17:38 |
General discussion | ||
|
FOC braking problem (FAULT_CODE_DRV) by iscle on Tue, 2018-05-29 15:16 |
29 |
by Zanooon97 Sat, 2023-03-18 20:11 |
General discussion | |
|
Can you use both axes on a 2-axis nunchuck/joystick controller with VESC? by adamdorr on Tue, 2019-12-31 22:05 |
6 |
by sanketh1691 Sat, 2021-10-09 00:45 |
General discussion | |
|
speed controller at low RPM by hagoston on Mon, 2021-03-08 13:54 |
3 |
by Elwin Sun, 2021-10-31 13:53 |
General discussion | |
|
/Slow/ top speed by Benrie on Fri, 2024-01-19 22:04 |
1 |
by vadicus Thu, 2024-01-25 06:55 |
General discussion | |
|
How to set a jog speed using an encoder by AK6302019 on Wed, 2019-08-07 15:42 |
by AK6302019 Wed, 2019-08-07 15:42 |
General discussion | ||
|
100V/250A Vesc for sale!!!!! by Fpvlee on Mon, 2021-11-08 03:59 |
2 |
by Svein Utne Fri, 2023-01-20 08:56 |
General discussion | |
|
GO-FOC G300 - shorted the USB connector shield to 72v by hedbrant on Tue, 2023-04-11 13:22 |
1 |
by hedbrant Thu, 2023-04-13 20:44 |
General discussion | |
|
Minimum speed push cart using arduino by BarBumble on Wed, 2021-05-12 09:29 |
by BarBumble Wed, 2021-05-12 09:29 |
General discussion | ||
|
Noise between VESC and microcontroller by onsokumaru on Tue, 2018-04-03 21:56 |
2 |
by fourchette Tue, 2018-11-20 21:32 |
General discussion | |
|
Current sensor and commanded current by galp on Fri, 2019-02-22 23:08 |
by galp Fri, 2019-02-22 23:08 |
General discussion | ||
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker on Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
General discussion | |
|
Stormcore 60D+ loses drive on one side by Big_McLargeHuge on Wed, 2022-01-26 05:01 |
1 |
by Big_McLargeHuge Wed, 2022-01-26 05:21 |
General discussion | |
|
motors wont turn by Jambi56 on Mon, 2022-09-26 01:48 |
2 |
by Zander rowley Mon, 2023-01-09 16:43 |
General discussion | |
|
Current Control issue VESC4 by yosoufe on Tue, 2018-03-20 09:28 |
5 |
by itchavenag Fri, 2019-09-13 12:06 |
General discussion | |
|
Struggling in startup BLDC in sensorless mode by dangminhducnbk on Fri, 2019-02-15 03:42 |
2 |
by dangminhducnbk Sun, 2019-02-17 12:48 |
General discussion | |
|
Improved low speed and full stop control with Hall by pf26 on Mon, 2020-06-08 19:33 |
4 |
by pf26 Tue, 2020-09-22 17:34 |
General discussion | |
|
problem sending with setRPM(float) repeatedly at a high rate by comes04 on Thu, 2023-08-24 14:49 |
by comes04 Thu, 2023-08-24 14:49 |
General discussion | ||
|
(Not) Stator saturation by Stupidspencer on Sun, 2019-10-13 00:34 |
4 |
by bittes Sat, 2020-05-09 14:46 |
General discussion | |
|
Insufficient torque at low RPM by isso777 on Sat, 2022-04-23 21:13 |
10 |
by frank Tue, 2022-05-03 08:18 |
General discussion |
Pages
