You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Using a VESC V4.12 for a machining lathe by Krampas on Sun, 2019-06-09 22:16 |
19 |
by Luke264 Wed, 2021-02-17 18:53 |
General discussion | |
Tell me how to accurately determine the type of engine FOC, BLDC by Valera1996 on Sun, 2020-02-09 18:53 |
8 |
by vadicus Mon, 2020-02-17 22:41 |
General discussion | |
Stator Saturation Compensation Mode by getinthebag on Tue, 2023-02-07 09:12 |
1 |
by benabelay@gmail.com Tue, 2024-02-27 23:22 |
General discussion | |
Tmotor U8 and VESC6 FOC by protontim on Tue, 2017-10-10 22:44 |
26 |
by magnus.w Sun, 2019-04-28 18:45 |
General discussion | |
. by faheemift on Tue, 2021-03-30 15:37 |
by faheemift Thu, 2021-04-01 13:58 |
General discussion | ||
Lanyard kill switch by craig w on Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
General discussion | |
Duty cycle-what does that control? by cromoly on Sat, 2018-11-24 01:11 |
2 |
by cromoly Sun, 2018-11-25 07:40 |
General discussion | |
Analog Throttle/Brake -- ADC2 does NOT cut power to the throttle? What is wrong? by 010203040506070809 on Fri, 2019-09-20 07:57 |
3 |
by striderkent Fri, 2019-09-20 21:54 |
General discussion | |
VESC to test e-Bike motor and car alternator as Torque Load..? by arifbustani on Thu, 2019-09-12 19:00 |
by arifbustani Thu, 2019-09-12 19:00 |
General discussion | ||
program motorstop for VTOL by Jan-Willem on Wed, 2020-04-29 18:55 |
4 |
by frank Thu, 2020-04-30 18:08 |
General discussion | |
Is there a way to use the 5 pin hall sensor with VESC? by Shivanshu Mahim on Fri, 2020-11-20 11:02 |
3 |
by Shivanshu Mahim Sat, 2020-11-21 19:34 |
General discussion | |
VESC Blink codes by ligi on Wed, 2022-03-16 12:36 |
1 |
by frank Wed, 2022-03-16 14:57 |
General discussion | |
VESC for BLDC Pump- motor settings by ar5000 on Thu, 2021-06-10 10:02 |
6 |
by frank Thu, 2021-06-10 11:42 |
General discussion | |
Vesc firmware to programmable Sabvoton ml60 controller. by Maciejwarloch on Tue, 2022-03-08 14:19 |
by Maciejwarloch Tue, 2022-03-08 14:19 |
General discussion | ||
forward, reverse, regen by ronmotor on Thu, 2022-11-10 22:37 |
2 |
by velolac Tue, 2022-11-15 12:06 |
General discussion | |
0 - 100% throttle in a sec by gadiati on Tue, 2019-04-02 21:45 |
1 |
by sam.vanratt Thu, 2019-04-04 18:40 |
General discussion | |
VESC behaviour as constant torque winch by devmonkey on Thu, 2020-07-09 23:43 |
4 |
by district9prawn Mon, 2020-08-10 13:21 |
General discussion | |
How to use an IMU and a PPM remote parallel by Gos1 on Tue, 2022-10-25 15:28 |
by Gos1 Wed, 2022-10-26 10:57 |
General discussion | ||
Wand Displaying Wrong Voltage %. by WastedYouth on Sat, 2021-10-23 17:37 |
by WastedYouth Sat, 2021-10-23 17:37 |
General discussion | ||
VESC as generator - settings confirmation by justinlsquire on Mon, 2022-06-06 02:44 |
by justinlsquire Mon, 2022-06-06 02:44 |
General discussion |