You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
ADC control not linear or smooth by arranto12 on Sat, 2021-11-13 23:23 |
4 |
by TechAUmNu Sun, 2021-11-14 01:03 |
General discussion | |
|
Brushless or brushed motor for autonomous rc-car by Joe_Lowtech on Thu, 2018-12-20 11:56 |
4 |
by Joe_Lowtech Tue, 2019-03-05 11:00 |
General discussion | |
|
program motorstop for VTOL by Jan-Willem on Wed, 2020-04-29 18:55 |
4 |
by frank Thu, 2020-04-30 18:08 |
General discussion | |
|
VESC behaviour as constant torque winch by devmonkey on Thu, 2020-07-09 23:43 |
4 |
by district9prawn Mon, 2020-08-10 13:21 |
General discussion | |
|
Vesc is not working by Patryk on Mon, 2018-10-08 18:48 |
4 |
by Patryk Fri, 2018-10-19 22:25 |
General discussion | |
|
Regen Braking not working by James Hamilton on Thu, 2022-05-26 16:08 |
4 |
by frank Wed, 2022-06-01 18:14 |
VESC Tool | |
|
dual vesc by badger1666 on Fri, 2018-09-21 09:10 |
4 |
by badger1666 Sat, 2018-09-29 15:45 |
General discussion | |
|
Non-Standard-BLDC-Motor by dekafive on Fri, 2020-05-22 19:55 |
4 |
by dekafive Mon, 2020-06-15 20:19 |
General discussion | |
|
Cannot get any PPM signals from Arduino. Or is it just the VESC tool? by MaxMaker1 on Thu, 2018-06-21 23:06 |
4 |
by tuloski Thu, 2018-09-13 09:36 |
VESC Tool | |
|
enertionboard focbox : is vesc_tool safe to use? by fourchette on Wed, 2018-11-07 23:49 |
4 |
by fourchette Tue, 2018-11-20 21:13 |
General discussion | |
|
PPM duty cycle option not being stored in EEPROM by wjpremerlani on Wed, 2022-06-08 12:49 |
4 |
by frank Thu, 2022-06-09 09:07 |
General discussion | |
|
Controlling BLDC Cordless Router with VESC by CthulhuLabs on Mon, 2020-05-25 16:58 |
4 |
by TheFallen Tue, 2020-06-23 09:44 |
General discussion | |
|
New Control Algorithm for asynchronous machines by ajpina on Sun, 2019-05-19 22:13 |
4 |
by Henque19 Wed, 2019-10-16 23:29 |
VESC Firmware | |
|
Protect psu from regenerative braking by KarlGreger on Tue, 2020-01-28 03:45 |
4 |
by marc.s.cohn@gma... Tue, 2020-07-07 21:11 |
General discussion | |
|
Flipsky 75/100 Mosfet short? by Michael Campbell on Mon, 2022-04-11 08:29 |
4 |
by Michael Campbell Tue, 2022-04-12 00:03 |
General discussion | |
|
Roll-to-start VESC by dsuresh on Fri, 2021-03-12 21:05 |
4 |
by robertkovax Fri, 2023-11-10 16:57 |
General discussion | |
|
Motor not Spinning Up During Setup Wizard by superjay on Tue, 2021-11-23 07:03 |
4 |
by superjay Wed, 2021-11-24 11:25 |
VESC Tool | |
|
Custom 12S VESC seems to be power limiting or something by nickw1881 on Sat, 2018-08-25 07:40 |
4 |
by nickw1881 Tue, 2018-09-18 05:56 |
Third Party Hardware | |
|
Improved low speed and full stop control with Hall by pf26 on Mon, 2020-06-08 19:33 |
4 |
by pf26 Tue, 2020-09-22 17:34 |
General discussion | |
|
(Not) Stator saturation by Stupidspencer on Sun, 2019-10-13 00:34 |
4 |
by bittes Sat, 2020-05-09 14:46 |
General discussion |
Pages
