You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Limp mode via CAN by totalgeek9224 on Mon, 2020-02-10 14:37 |
3 |
by A2 Wed, 2021-09-08 21:20 |
Feature Requests | |
|
How different of VESC 6 and VESC 4 by Ken_chen on Thu, 2018-05-17 18:13 |
3 |
by ripperpc Mon, 2020-05-04 07:58 |
General discussion | |
|
Two Vesc6 MKV twin arrays ESC's - BMS CAN BUS connectivity by Spaceman on Fri, 2022-05-27 16:22 |
3 |
by Spaceman Fri, 2022-06-03 15:36 |
General discussion | |
|
Generator app by arvidb on Sat, 2018-09-22 01:03 |
3 |
by stiganielsen Fri, 2019-09-20 14:29 |
VESC Firmware | |
|
DRV 8302 Under Voltage error by Oyta on Fri, 2017-09-01 20:52 |
3 |
by benjamin Tue, 2017-09-05 21:39 |
VESC6 Beta | |
|
Programming NRF51822 Module with ST-Link v2 by koralle on Wed, 2018-07-11 12:06 |
3 |
by koralle Sun, 2018-07-15 01:28 |
General discussion | |
|
Controlling general BLDC motors by sinned6915 on Wed, 2020-08-19 01:56 |
3 |
by TheFallen Sun, 2020-08-23 16:51 |
General discussion | |
|
Maker X Mini VESC burned at 46V. My fault or shitty quality? by smileandbeware on Mon, 2019-11-18 10:53 |
3 |
by frank Thu, 2019-12-26 15:27 |
Third Party Hardware | |
|
Undervoltage Fault by gazlinux on Tue, 2022-02-08 02:26 |
3 |
by 67RS427 Fri, 2022-10-21 20:53 |
General discussion | |
|
bootloader destroied by notger on Tue, 2017-09-19 19:55 |
3 |
by dinamee Sat, 2018-01-13 10:09 |
General discussion | |
|
choice between 2 eRPM by elektrojodler on Thu, 2022-05-05 15:22 |
3 |
by drummerboy5408 Tue, 2022-05-10 04:11 |
General discussion | |
|
Hub motor stutters at low RPM by winpark on Wed, 2020-09-02 00:53 |
3 |
by vadicus Tue, 2020-09-15 18:14 |
General discussion | |
|
Flux linkage detection failed by Count1310 on Sat, 2020-08-22 16:30 |
3 |
by drummerboy5408 Wed, 2022-04-13 07:42 |
General discussion | |
|
Serial Interface by dougm on Thu, 2017-08-17 04:33 |
3 |
by Pimousse Sat, 2017-08-19 10:34 |
VESC6 Beta | |
|
Downloading VESC tool on a mac? by Taliesin on Mon, 2018-04-30 01:28 |
3 |
by txdad Fri, 2021-08-27 17:41 |
General discussion | |
|
Initial startup time by rxty on Thu, 2022-06-02 18:38 |
3 |
by sifourquier Sun, 2024-02-25 23:16 |
VESC Firmware | |
|
Question about COMM_GET_IMU_DATA packet by rrzaripov on Wed, 2020-03-04 00:28 |
3 |
by Addy Fri, 2020-04-24 06:49 |
VESC Tool | |
|
Bus bar and heavy copper PCBs by lopezcontreras on Mon, 2019-01-28 17:40 |
3 |
by galp Thu, 2019-01-31 20:20 |
Third Party Hardware | |
|
I put the wrong firmware (48) on my 4.12 vesc from Hobbyking by drawliphant on Mon, 2019-01-14 22:09 |
3 |
by drawliphant Wed, 2019-01-16 08:19 |
VESC Firmware | |
|
FFT in VESC Tool by RSR on Thu, 2018-05-31 14:37 |
3 |
by TechAUmNu Thu, 2018-05-31 16:28 |
VESC Tool |
Pages
