You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
VESC tool repeatedly not recognising firmware by granstubbe on Sun, 2019-05-19 20:59 |
10 |
by Brian123 Sat, 2022-05-21 00:46 |
VESC Tool | |
PPM with ADC by vufmihai on Mon, 2019-12-30 09:09 |
9 |
by getinthebag Fri, 2024-01-05 06:52 |
Feature Requests | |
Acceleration control to desired RPM by bjohns on Fri, 2018-07-20 22:08 |
9 |
by arvidb Thu, 2018-08-09 21:15 |
General discussion | |
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker on Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
General discussion | |
FAULT_CODE_UNDER_VOLTAGE by alexantosh on Mon, 2021-11-29 09:26 |
9 |
by heravinluca Thu, 2022-08-04 04:19 |
VESC Tool | |
Help is there an issue with my new Vesc 6 by avis on Sat, 2017-09-30 15:21 |
9 |
by frank Wed, 2017-10-04 17:10 |
General discussion | |
vesc tool 1.25 not opening. by osis on Tue, 2019-10-29 20:50 |
9 |
by flyingbrike Wed, 2021-09-08 09:06 |
VESC Tool | |
Failure in Motor Set Up by Toshi Sharma on Tue, 2022-01-11 15:19 |
9 |
by frank Thu, 2022-01-13 14:15 |
General discussion | |
VESC Tool wont start by w31x on Wed, 2020-03-11 19:30 |
9 |
by SUB13 Sun, 2024-02-11 14:43 |
VESC Tool | |
Invert motor direction. by Sanjoy on Thu, 2017-06-15 23:31 |
9 |
by Roger Wolff Mon, 2017-06-19 16:00 |
VESC6 Beta | |
FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 by TB_Poule on Sat, 2021-04-10 17:26 |
9 |
by bayetan Thu, 2023-09-21 16:24 |
General discussion | |
VESC with Raspberry Pi 3 by Antonio Rodrígu... on Sun, 2018-06-03 18:54 |
9 |
by ShortCircuit Thu, 2018-06-28 15:33 |
General discussion | |
(solved) Configuration smooth motordirection change by horak2084 on Mon, 2019-02-25 20:44 |
9 |
by fpagac Sat, 2020-04-25 17:17 |
VESC Firmware | |
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON on Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
General discussion | |
Third party Android/iOS app by vadicus on Tue, 2022-07-19 21:51 |
9 |
by teibill Sat, 2024-04-13 19:32 |
Third Party Hardware | |
Trampa VESC 100/250 suitable for heavy applications? by nojjan on Thu, 2022-12-29 13:52 |
9 |
by vadicus Wed, 2023-03-01 06:26 |
General discussion | |
Firmware for 4.xx VESC in new VESC Tool? by sl33py on Wed, 2017-06-28 21:27 |
9 |
by sl33py Fri, 2017-07-14 08:29 |
VESC6 Beta | |
Motor braking - shorting phases by rok340 on Thu, 2021-01-21 07:49 |
9 |
by dpeinado Mon, 2022-02-14 12:36 |
General discussion | |
VESC Tool Compatible With FW 3.34 by a.ceviker on Sun, 2018-07-29 11:38 |
9 |
by bitmixer Fri, 2020-02-21 22:18 |
VESC Tool | |
highest battery current with 6.6? by devin on Tue, 2020-01-14 16:05 |
9 |
by devin Wed, 2020-01-15 01:05 |
General discussion |