You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Duty vs RPM for smooth start and slow running by Davideo on Tue, 2018-04-24 14:42 |
by Davideo Tue, 2018-04-24 14:42 |
General discussion | ||
wand brake to reverse by michmg on Tue, 2019-09-10 23:54 |
3 |
by michmg Sat, 2019-09-14 20:16 |
General discussion | |
Controlling (HB) Braking from Arduino by Bruce on Sat, 2021-02-27 00:23 |
by Bruce Sat, 2021-02-27 00:23 |
General discussion | ||
Sudden hard acceleration at around 30 km/h. Help by kristofferbenjaminw on Tue, 2022-10-04 17:31 |
4 |
by Chris Barth Tue, 2022-10-11 20:05 |
General discussion | |
Is electronic brake always REGEN? by Tilman Baumann on Tue, 2018-04-10 11:16 |
19 |
by henxan Sun, 2019-11-17 18:30 |
General discussion | |
How does regenerative braking get enough voltage from my motor to charge my battery from ? by cnd on Wed, 2020-09-16 16:54 |
7 |
by flydr2 Mon, 2023-02-27 22:21 |
General discussion | |
Pid_Speed is braking despite no brake option by Flyingtux on Thu, 2022-04-07 09:41 |
2 |
by Flyingtux Thu, 2022-04-07 15:49 |
General discussion | |
Sensored mode studering by dtmpro621 on Thu, 2023-03-02 04:40 |
by dtmpro621 Thu, 2023-03-02 05:25 |
General discussion | ||
Switching between hall and observer by eptv on Thu, 2019-12-05 08:49 |
1 |
by frank Thu, 2019-12-05 10:54 |
General discussion | |
VESC 4.12 FW5.02 CAN status messages is spamming bus, external controller, SOLVED: NEEDED INIT! by Offline on Mon, 2021-05-03 14:57 |
1 |
by Offline Tue, 2021-05-04 10:03 |
General discussion | |
Improper feedback from VESC with low speed ( BEMF ) by Pranit Bhamare on Tue, 2023-02-14 07:16 |
2 |
by Pranit Bhamare Fri, 2023-02-17 04:57 |
General discussion | |
Recommended way to implement CAN-bus communication using a Linux based controller by toma on Tue, 2019-06-11 08:32 |
8 |
by toma Thu, 2019-06-13 07:43 |
General discussion | |
Install VESC on ubuntu 18.04 bionic by rest_vesc_001 on Tue, 2020-12-08 15:34 |
by rest_vesc_001 Tue, 2020-12-08 15:34 |
General discussion | ||
Sensorless BLDC motor by Pelle van wijk on Sun, 2019-11-24 15:18 |
1 |
by frank Thu, 2019-11-28 09:56 |
General discussion | |
Negative current reporting at high erpm in no-load setup by mcdanny on Sun, 2021-01-17 23:04 |
1 |
by moto_guy Sat, 2021-01-30 04:53 |
General discussion | |
Vesc 100/250 for unsensored brushless motors by jmurba on Fri, 2022-08-05 12:05 |
3 |
by velolac Fri, 2022-08-12 22:14 |
General discussion | |
Power Switch by flyingbrike on Wed, 2021-09-08 13:47 |
by flyingbrike Wed, 2021-09-08 13:47 |
General discussion | ||
Third Party Hardware Section - closed? by vadicus on Mon, 2023-07-03 07:15 |
1 |
by vadicus Wed, 2023-07-12 20:11 |
General discussion | |
Smooth control 3 phase sensored motor by spacewalker on Thu, 2020-07-23 07:25 |
4 |
by vadicus Fri, 2020-11-13 19:18 |
General discussion | |
Difference between ERPM and Duty Cycle by dormanae on Wed, 2022-02-23 17:21 |
1 |
by j.konrad Thu, 2022-02-24 02:08 |
General discussion |