You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Starter motor stoping for no apparent reason by Bexy on Wed, 2022-08-03 18:07 |
3 |
by Faheem Wed, 2023-10-25 08:56 |
General discussion | |
|
vesc6 help with hub motor by badger1666 on Thu, 2018-12-20 18:36 |
4 |
by badger1666 Fri, 2018-12-21 06:03 |
General discussion | |
|
VESC/FOC developer needed by CAYAGO_MS on Thu, 2020-04-30 14:23 |
by CAYAGO_MS Thu, 2020-04-30 14:23 |
General discussion | ||
|
How to control two Can-connected motors separately from microcontroller. by kkkeisuke on Sun, 2021-06-20 06:47 |
by kkkeisuke Sun, 2021-06-20 12:05 |
General discussion | ||
|
Request: Report hall sensor tables. by Roger Wolff on Thu, 2018-05-17 15:28 |
7 |
by Tilman Baumann Mon, 2018-08-06 12:24 |
General discussion | |
|
Dual Motor Software "Limited Slip" Differential by luky on Thu, 2021-06-10 10:43 |
1 |
by frank Thu, 2021-06-10 11:07 |
General discussion | |
|
Can bus and BLDC vs FOC by Torbjorn on Fri, 2022-11-11 11:08 |
4 |
by Torbjorn Tue, 2022-11-15 14:37 |
General discussion | |
|
Current control and duty cycle issues. by ESCam on Tue, 2019-04-02 22:55 |
by ESCam Tue, 2019-04-02 22:55 |
General discussion | ||
|
Encoder position resetting to 0° by Michelle90 on Tue, 2022-10-25 18:55 |
1 |
by GijsB Sun, 2022-10-30 20:17 |
General discussion | |
|
Can bus communication. by Piamen on Wed, 2019-11-27 06:47 |
by Piamen Wed, 2019-11-27 06:47 |
General discussion | ||
|
Using VESC to drive sensorless linear motor to simulate on/off solenoid by cmcraeslo on Wed, 2020-07-01 09:15 |
1 |
by pf26 Mon, 2020-07-06 11:10 |
General discussion | |
|
how to delete pc install, struggling to get the mobile program to work :) by jon218white on Thu, 2021-02-18 20:47 |
1 |
by TheFallen Fri, 2021-02-19 00:31 |
General discussion | |
|
DRV8302 sensibility by lurch on Sat, 2021-10-23 23:37 |
19 |
by lurch Sat, 2021-10-30 10:13 |
General discussion | |
|
VESC 6 motor setup: Resistance measurement jumps by thomasjfox on Mon, 2017-10-09 20:42 |
2 |
by thomasjfox Sat, 2017-10-28 21:57 |
General discussion | |
|
Communication with Vesc Tools by faheemift on Tue, 2021-02-09 16:08 |
8 |
by beatrixena Sat, 2021-02-20 09:11 |
General discussion | |
|
Starting rotation by changing duty cicle- current increases shortly (ms) and dcreases immediately to 0A by simon_snow on Wed, 2021-10-06 22:15 |
4 |
by simon_snow Fri, 2021-10-08 12:49 |
General discussion | |
|
Position control of brushed dc motor with Vesc and REV through bore encoder by Greasy_D on Wed, 2023-03-29 20:17 |
14 |
by EnDeR_WiGiN Fri, 2023-04-14 17:48 |
General discussion | |
|
How is Motor Temperature measured? by shimdidly on Mon, 2017-10-02 07:52 |
4 |
by drummerboy5408 Thu, 2022-05-05 05:06 |
General discussion | |
|
How to Write Serial Communication Program Not Applicable to RTOS by Jack_Li on Fri, 2019-07-05 06:55 |
by Jack_Li Fri, 2019-07-05 06:58 |
General discussion | ||
|
On MOSFET choice and replacement by DarioP on Wed, 2020-09-30 14:11 |
5 |
by TheFallen Fri, 2020-10-02 10:57 |
General discussion |
Pages
