You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Remote Control and Bluetooth at same time by Grave on Thu, 2022-04-07 22:03 |
by Grave Fri, 2022-04-08 10:06 |
Third Party Hardware | ||
|
Remote control that works with the VESC 6 by Oyta on Thu, 2017-06-08 19:33 |
14 |
by fedestanco Fri, 2017-06-23 19:18 |
VESC6 Beta | |
|
Remote not receiving telemetry data by jasson on Sun, 2022-02-06 04:21 |
2 |
by jasson Sun, 2022-02-06 05:56 |
General discussion | |
|
Remote pairs but motor does not spin after VESC tool use by frunobulax on Fri, 2025-04-11 18:26 |
by frunobulax Fri, 2025-04-11 18:26 |
General discussion | ||
|
Removing low speed openloop FOC parking brake mode from FW by rodread on Thu, 2018-03-08 15:01 |
4 |
by arvidb Wed, 2018-06-06 19:02 |
General discussion | |
|
Renaming the versions to avoid confusion when downloading. by ThierryGTLTS on Fri, 2017-09-08 12:54 |
4 |
by ThierryGTLTS Sun, 2017-10-15 19:02 |
Feature Requests | |
|
Repairing by lamak on Thu, 2025-06-26 07:08 |
2 |
by ispor4en Fri, 2025-06-27 21:15 |
General discussion | |
|
Replacement drv8301 vesc 6.6 by jneumann on Sat, 2020-05-16 06:11 |
1 |
by doomy1986 Sat, 2020-05-16 19:53 |
Third Party Hardware | |
|
replacing in wheel controler with vesc 6 mk vi? by arni on Tue, 2024-11-12 15:40 |
by arni Wed, 2024-11-13 15:04 |
General discussion | ||
|
Reprogram VESC for sensorless motor by Christopherinco... on Thu, 2020-09-03 00:10 |
2 |
by vadicus Thu, 2020-09-03 01:14 |
General discussion | |
|
Repurposed Hyundai Ioniq HSG Hybrid Starter Generator as motor - crunching/cogging by patracy on Sat, 2025-04-12 04:42 |
by patracy Sat, 2025-04-12 04:42 |
General discussion | ||
|
Request Feature to add minimum Battery Voltage value in addition to duty cycle for field weakening by aquaponiccowboy on Mon, 2022-10-17 04:49 |
by aquaponiccowboy Mon, 2022-10-17 04:50 |
Feature Requests | ||
|
Request for Example: Can communication with Libcanard by WoofyBunny on Fri, 2022-05-13 03:44 |
by WoofyBunny Fri, 2022-05-13 03:45 |
VESC Firmware | ||
|
Request: Report hall sensor tables. by Roger Wolff on Thu, 2018-05-17 15:28 |
7 |
by Tilman Baumann Mon, 2018-08-06 12:24 |
General discussion | |
|
Requesting fault codes over UART by spork on Wed, 2020-06-24 09:02 |
1 |
by Pimousse Wed, 2020-07-01 12:50 |
General discussion | |
|
Requesting VESC fault codes via UART by spork on Fri, 2020-06-26 21:52 |
1 |
by f.damien12 Sun, 2022-04-03 18:27 |
VESC Firmware | |
|
Reset parameters by nidhirao on Mon, 2019-12-23 10:57 |
by nidhirao Mon, 2019-12-23 10:57 |
VESC Tool | ||
|
resistance and inductance value changes when each measurement by alexshen2012 on Fri, 2022-07-01 05:45 |
by alexshen2012 Fri, 2022-07-01 05:45 |
General discussion | ||
|
resistance and inductance value changes when each measurement by alexshen2012 on Fri, 2022-07-01 05:42 |
by alexshen2012 Fri, 2022-07-01 05:42 |
General discussion | ||
|
Reusing pin in custom application by Pechvogel on Wed, 2021-01-13 07:12 |
by Pechvogel Wed, 2021-01-13 07:12 |
VESC Firmware |
Pages
