You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Adding support for three phase shunts... by Roger Wolff on Wed, 2017-11-08 16:03 |
3 |
by georpo Tue, 2018-03-13 14:34 |
VESC Firmware | |
|
[solved] Firmware 5.01 gcc compile fail.. need some insight by Bill Somerville on Tue, 2020-11-03 19:44 |
by Bill Somerville Fri, 2020-11-06 23:20 |
VESC Firmware | ||
|
Compiled Firmware in limited mode by sirAnton on Sat, 2026-03-21 10:13 |
by sirAnton Sat, 2026-03-21 10:13 |
VESC Firmware | ||
|
Compiled Firmware 5.02 does not work by sirAnton on Wed, 2021-01-27 08:19 |
10 |
by alexantosh Wed, 2021-12-01 18:53 |
VESC Firmware | |
|
CAN sends error frame by dgarciasoto on Wed, 2022-04-27 07:11 |
2 |
by fingerprintdax Thu, 2025-10-02 00:46 |
VESC Firmware | |
|
Problems getting Cruise control to run properly with the new wand - dual VESC6 by MaddiQ on Mon, 2019-09-16 19:36 |
by MaddiQ Mon, 2019-09-16 19:36 |
VESC Firmware | ||
|
[Contributing][FOC] injected ADC and code clarity by Guillaume227 on Fri, 2017-12-15 18:00 |
1 |
by Roger Wolff Sat, 2017-12-16 13:21 |
VESC Firmware | |
|
Fimware 5.1 - where is the VESC_servoout.bin? by JackSilb on Tue, 2020-04-28 06:37 |
8 |
by udayravuri Tue, 2023-03-28 00:08 |
VESC Firmware | |
|
flipsky 75100 v2 by temas on Mon, 2026-06-22 13:40 |
2 |
by szlong Tue, 2026-06-23 11:26 |
VESC Firmware | |
|
Hall sensor detection failed (AWD setup) by frameto on Tue, 2018-10-02 22:02 |
1 |
by ronmotor Tue, 2020-10-27 02:20 |
VESC Firmware | |
|
running VESC firmware on Nucleo-f401re by a_babraunitski on Sat, 2023-03-25 22:21 |
by a_babraunitski Sat, 2023-03-25 22:22 |
VESC Firmware | ||
|
BLDC switching frequency by tuloski on Wed, 2018-09-19 13:18 |
1 |
by bauck Tue, 2020-11-17 17:08 |
VESC Firmware | |
|
BLDC control in FOC mode by da_rul0r on Fri, 2019-08-16 15:32 |
2 |
by sanketh1691 Fri, 2021-11-05 19:05 |
VESC Original Hardware | |
|
75/300 Layout or gerbers by Chapel81 on Fri, 2020-08-28 21:27 |
3 |
by Chapel81 Wed, 2020-09-09 16:24 |
VESC Original Hardware | |
|
Getting RPM data from VESC 4.12 by EmirDns on Wed, 2022-01-05 21:20 |
by EmirDns Wed, 2022-01-05 21:20 |
VESC Original Hardware | ||
|
Need advice : repair , vesc 4.12, vesc 6.4 or wait ? by frameto on Mon, 2017-11-20 21:57 |
2 |
by frameto Wed, 2017-11-22 22:01 |
VESC Original Hardware | |
|
75/300 R3 and metr.at wird iOS metr App by nice2cu on Sun, 2020-09-13 20:51 |
by nice2cu Sun, 2020-09-13 20:51 |
VESC Original Hardware | ||
|
VESC 6 Plus reseting settings and firmware by granstubbe on Fri, 2020-01-10 18:31 |
2 |
by ozcankosar Fri, 2022-11-25 22:18 |
VESC Original Hardware | |
|
Hub motor e-bike not recognized by olivierskypullc... on Tue, 2019-04-16 11:06 |
3 |
by Ampit Fri, 2023-09-29 12:38 |
VESC Original Hardware | |
|
Bringup, pinouts, general manual... where to find? by kubark42 on Sun, 2021-03-07 03:32 |
7 |
by smith2e7 Tue, 2023-01-24 15:34 |
VESC Original Hardware |
Pages
