You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
FFT in VESC Tool by RSR on Thu, 2018-05-31 14:37 |
3 |
by TechAUmNu Thu, 2018-05-31 16:28 |
VESC Tool | |
|
Adding support for three phase shunts... by Roger Wolff on Wed, 2017-11-08 16:03 |
3 |
by georpo Tue, 2018-03-13 14:34 |
VESC Firmware | |
|
Reverse safety function by rich on Tue, 2017-09-05 10:14 |
3 |
by rich Wed, 2017-09-06 11:07 |
Feature Requests | |
|
SPINTEND UBOX 100v100a x2 or Flipsky 75100 100v100a x2 by DuckyTheDuck on Mon, 2022-09-26 12:07 |
3 |
by AngelKillR Wed, 2022-09-28 05:06 |
General discussion | |
|
Mosfet Discussion by WalterWitt on Mon, 2022-04-18 20:38 |
3 |
by vadicus Thu, 2022-04-21 00:01 |
Third Party Hardware | |
|
Programming NRF51822 Module with ST-Link v2 by koralle on Wed, 2018-07-11 12:06 |
3 |
by koralle Sun, 2018-07-15 01:28 |
General discussion | |
|
Controlling general BLDC motors by sinned6915 on Wed, 2020-08-19 01:56 |
3 |
by TheFallen Sun, 2020-08-23 16:51 |
General discussion | |
|
Maker X Mini VESC burned at 46V. My fault or shitty quality? by smileandbeware on Mon, 2019-11-18 10:53 |
3 |
by frank Thu, 2019-12-26 15:27 |
Third Party Hardware | |
|
Undervoltage Fault by gazlinux on Tue, 2022-02-08 02:26 |
3 |
by 67RS427 Fri, 2022-10-21 20:53 |
General discussion | |
|
choice between 2 eRPM by elektrojodler on Thu, 2022-05-05 15:22 |
3 |
by drummerboy5408 Tue, 2022-05-10 04:11 |
General discussion | |
|
Hub motor stutters at low RPM by winpark on Wed, 2020-09-02 00:53 |
3 |
by vadicus Tue, 2020-09-15 18:14 |
General discussion | |
|
Flux linkage detection failed by Count1310 on Sat, 2020-08-22 16:30 |
3 |
by drummerboy5408 Wed, 2022-04-13 07:42 |
General discussion | |
|
Downloading VESC tool on a mac? by Taliesin on Mon, 2018-04-30 01:28 |
3 |
by txdad Fri, 2021-08-27 17:41 |
General discussion | |
|
Initial startup time by rxty on Thu, 2022-06-02 18:38 |
3 |
by sifourquier Sun, 2024-02-25 23:16 |
VESC Firmware | |
|
Question about COMM_GET_IMU_DATA packet by rrzaripov on Wed, 2020-03-04 00:28 |
3 |
by Addy Fri, 2020-04-24 06:49 |
VESC Tool | |
|
Bus bar and heavy copper PCBs by lopezcontreras on Mon, 2019-01-28 17:40 |
3 |
by galp Thu, 2019-01-31 20:20 |
Third Party Hardware | |
|
I put the wrong firmware (48) on my 4.12 vesc from Hobbyking by drawliphant on Mon, 2019-01-14 22:09 |
3 |
by drawliphant Wed, 2019-01-16 08:19 |
VESC Firmware | |
|
Trampa VESC6 USB connectivity problem caused by usb hub? by hagoston on Tue, 2021-06-01 10:27 |
4 |
by hagoston Wed, 2021-06-02 09:27 |
General discussion | |
|
Hooking up two or more motor drivers to the same MCU by darkclaude on Thu, 2019-06-20 10:02 |
4 |
by skyline1970 Wed, 2019-07-31 13:53 |
Third Party Hardware | |
|
No USB with latest VESC FW on 4.12 hardware by chris1seto on Thu, 2019-04-04 04:01 |
4 |
by dp Wed, 2020-12-02 13:01 |
VESC Firmware |
Pages
