You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
esc tester by FatsoBatso on Wed, 2021-02-24 18:05 |
1 |
by skyline1970 Fri, 2021-02-26 14:55 |
General discussion | |
|
Vesc red LED on by dsuresh on Wed, 2021-02-24 18:01 |
by dsuresh Wed, 2021-02-24 18:01 |
General discussion | ||
|
display readings by FatsoBatso on Wed, 2021-02-24 18:01 |
by FatsoBatso Wed, 2021-02-24 18:01 |
General discussion | ||
|
as5047d drift?,Vd voltage -10 by ziumus on Sat, 2021-02-20 20:38 |
3 |
by ziumus Tue, 2021-02-23 22:08 |
General discussion | |
|
anti theft possible? by hummina on Tue, 2021-02-23 07:44 |
by hummina Tue, 2021-02-23 07:44 |
General discussion | ||
|
VESC on Chromebook? by Boa1277 on Sun, 2021-02-21 20:49 |
by Boa1277 Sun, 2021-02-21 20:49 |
General discussion | ||
|
Communication with Vesc Tools by faheemift on Tue, 2021-02-09 16:08 |
8 |
by beatrixena Sat, 2021-02-20 09:11 |
General discussion | |
|
PWM connection for a remote by dsuresh on Fri, 2021-02-19 19:17 |
by dsuresh Fri, 2021-02-19 19:17 |
General discussion | ||
|
VESC controlled by CAN by j.m on Wed, 2021-02-17 10:51 |
1 |
by TheFallen Fri, 2021-02-19 00:52 |
General discussion | |
|
how to delete pc install, struggling to get the mobile program to work :) by jon218white on Thu, 2021-02-18 20:47 |
1 |
by TheFallen Fri, 2021-02-19 00:31 |
General discussion | |
|
Hoverboard motors not spinning when manually controlled, work when doing hall test etc. by VK2EVA on Fri, 2020-12-25 22:01 |
2 |
by ATHIVEL Thu, 2021-02-18 15:45 |
General discussion | |
|
Using a VESC V4.12 for a machining lathe by Krampas on Sun, 2019-06-09 22:16 |
19 |
by Luke264 Wed, 2021-02-17 18:53 |
General discussion | |
|
PID Position Controller by IanG on Wed, 2020-03-25 03:05 |
5 |
by Luke264 Wed, 2021-02-17 18:53 |
General discussion | |
|
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON on Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
General discussion | |
|
UART CAN forwarding by frankus on Tue, 2019-01-29 16:07 |
4 |
by frankus Tue, 2021-02-16 06:35 |
General discussion | |
|
Using vesc between many motors by EliProtiva on Tue, 2021-02-16 05:32 |
by EliProtiva Tue, 2021-02-16 05:32 |
General discussion | ||
|
advice on position control by feskarn on Mon, 2021-02-15 14:47 |
by feskarn Mon, 2021-02-15 14:47 |
General discussion | ||
|
Adding a Openloop COMM Comand by JulianT on Sun, 2021-01-17 21:27 |
2 |
by JulianT Mon, 2021-02-15 12:17 |
Feature Requests | |
|
Adding a Openloop COMM Comand by JulianT on Sun, 2021-01-17 21:27 |
2 |
by JulianT Mon, 2021-02-15 12:17 |
General discussion | |
|
Vesc Tools by Don on Sat, 2021-02-13 14:25 |
by Don Sat, 2021-02-13 14:25 |
General discussion |
Pages
