You are here
Third Party Hardware
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Motors with known valid configurations by doctarr » Fri, 2021-01-01 14:28 |
4 |
by doctarr Sat, 2021-01-09 14:44 |
|
|
Motor spins only with outside help by asaf123098 » Thu, 2019-04-04 06:52 |
4 |
by dekafive Thu, 2019-06-20 11:36 |
|
|
Motor Setup issues e-Snowboard by arosenthal » Fri, 2020-09-18 21:10 |
3 |
by etadada12 Sun, 2020-11-29 02:17 |
|
|
Motor not spinning NO FAULTS by 123seaborder » Mon, 2019-06-10 21:46 |
1 |
by gogglespast Sat, 2019-09-14 08:34 |
|
|
Motor is too loud, are there settings to quiet it? by Jason Toews » Thu, 2021-09-23 20:49 |
2 |
by Laurie Forbes Thu, 2021-09-30 18:57 |
|
|
Motor detection accuracy in 3rd party hardware (old FW vs new FW) by shaman » Tue, 2020-02-25 16:03 |
3 |
by vadicus Wed, 2020-02-26 19:09 |
|
|
Motor controller commercial test benches by lopezcontreras » Mon, 2019-12-16 15:31 |
0 |
by lopezcontreras Mon, 2019-12-16 15:31 |
|
|
Mosfet Discussion by WalterWitt » Mon, 2022-04-18 20:38 |
3 |
by vadicus Thu, 2022-04-21 00:01 |
|
|
Modified version of mini4,during motor detection，fault_code_drv-11 was reported by qdxiatao » Mon, 2022-10-31 07:42 |
0 |
by qdxiatao Mon, 2022-10-31 07:42 |
|
|
mksvesc 84200 by Nubi » Sat, 2024-08-10 00:48 |
2 |
by Huang_jh Thu, 2024-10-17 12:55 |
|
|
MINI4 (Page: 1, 2)
by antonchromjak » Sun, 2017-11-26 16:08 |
61 |
by roque.canales Fri, 2023-09-29 13:54 |
|
|
Mini/micro/nano VESC solutions? by Cham » Mon, 2020-09-21 17:34 |
3 |
by Cham Thu, 2020-09-24 12:15 |
|
|
MINI FOC from MakerX by YUTW » Thu, 2019-08-08 11:17 |
1 |
by speed3r Tue, 2019-08-13 10:17 |
|
|
MINI 4 having DRV8301 in mini4.h ! by snakeplissken » Fri, 2023-11-24 20:58 |
1 |
by justlovescience Tue, 2024-02-06 16:36 |
|
|
MICRO Module by F4metz » Sat, 2019-03-02 15:10 |
3 |
by chuttney1 Sun, 2019-03-03 18:54 |
|
|
Maytech VESC keeps startup spinning slowly by Snorreman » Mon, 2018-09-24 09:57 |
0 |
by Snorreman Mon, 2018-09-24 09:57 |
|
|
Maytech VESC duty cycle & PID control problems by subodh.malgonde » Mon, 2018-10-01 11:49 |
1 |
by subodh.malgonde Tue, 2018-10-02 11:59 |
|
|
Maytech VESC 6 FOC turn off without fault at high erpm, blower by gabrield » Fri, 2020-05-15 01:16 |
2 |
by ImperialSB Thu, 2021-04-22 17:54 |
|
|
Maytech VESC 4.10 UART issues by LogixCraft » Tue, 2018-09-25 03:13 |
0 |
by LogixCraft Tue, 2018-09-25 03:13 |
|
|
Maytech SUPERFOC6.8 50A sub zero cooling for fun and burst power. Mosfet power loss? by Gargazol » Tue, 2020-10-20 14:12 |
1 |
by TheFallen Tue, 2020-10-27 16:38 |
|
|
maytech mto91hbm-nh motors hal sensor by nolander » Thu, 2019-01-10 00:01 |
1 |
by sunsam8 Thu, 2019-01-10 11:15 |
|
|
MAYTECH ESC6 200A runs fine on 6s, faults immediately on 12s by mxpro32 » Sun, 2019-06-30 21:39 |
3 |
by TechAUmNu Tue, 2019-08-13 10:21 |
|
|
Maytech esc 5V rail reads 0.5v by hhhhghg » Fri, 2018-09-14 13:23 |
0 |
by hhhhghg Fri, 2018-09-14 13:23 |
|
|
Maytech 200A does not work in FOC, will a A200S work better? by doom » Wed, 2019-08-07 20:40 |
1 |
by TechAUmNu Fri, 2019-08-09 21:01 |
|
|
Maytech 100a ESC by NOldfield » Sat, 2023-04-22 08:51 |
0 |
by NOldfield Mon, 2023-04-24 15:32 |
Log in to post new content in the forum.
