You are here
Third Party Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
using hall effect sensor for rpm detection by meisterpro » Wed, 2021-03-03 01:26 |
1 |
by vadicus Thu, 2021-03-04 18:12 |
|
|
Flipsky Mini FSESC4.2 Questions by Laurie Forbes » Sat, 2021-10-02 18:54 |
1 |
by skyline1970 Fri, 2021-10-29 12:09 |
|
|
Maytech SUPERFOC6.8 50A sub zero cooling for fun and burst power. Mosfet power loss? by Gargazol » Tue, 2020-10-20 14:12 |
1 |
by TheFallen Tue, 2020-10-27 16:38 |
|
|
One remote, two FSESC4.20 (wirelessly)? by fogus » Mon, 2020-10-26 17:42 |
1 |
by Rashid1992 Wed, 2022-08-31 10:32 |
|
|
VESC Design - Review and Bringup - 150V - 20A by ripperpc » Sat, 2019-09-21 17:30 |
1 |
by TechAUmNu Mon, 2019-09-30 14:34 |
|
|
I can't communicate with the VESC-Clone by Savavit » Sun, 2019-10-27 17:42 |
1 |
by vadicus Thu, 2019-11-07 06:48 |
|
|
Flipsky FSESC v4.20 suddenly flashing error code by JustWantRun » Thu, 2020-08-06 18:44 |
1 |
by JustWantRun Thu, 2020-08-06 19:22 |
|
|
Can't update firmware FSESC 4.12 by TimBilliet » Tue, 2019-11-26 21:52 |
1 |
by TechAUmNu Wed, 2019-11-27 14:47 |
|
|
What about using the Votol em150 3kw 48-72v? by Arpanx » Sat, 2020-03-21 11:23 |
1 |
by vadicus Mon, 2020-03-23 20:15 |
|
|
Maytech 200A does not work in FOC, will a A200S work better? by doom » Wed, 2019-08-07 20:40 |
1 |
by TechAUmNu Fri, 2019-08-09 21:01 |
|
|
Custom 75_150 board noise and not synchronized by lacondro » Mon, 2022-08-01 09:06 |
1 |
by lacondro Tue, 2022-08-02 13:26 |
|
|
Chinese board questions. I don't know where to start by seanus4u@gmail.com » Mon, 2022-08-15 02:00 |
1 |
by AngelKillR Wed, 2022-09-28 04:44 |
|
|
Diagnosing FSESC4.20 dead/weird phase (?) by josephduchesne » Sun, 2022-09-18 23:52 |
1 |
by skyline1970 Thu, 2022-11-24 20:23 |
|
|
Flipsky 75200 + Flipsky 85135 12kw only 2kw output by giver » Thu, 2022-10-27 21:00 |
1 |
by skyline1970 Thu, 2022-11-24 20:08 |
|
|
Focbox unity FW Version 5.3 support by theparadoxdoge » Thu, 2022-11-17 06:45 |
1 |
by frank Thu, 2022-11-17 17:56 |
|
|
48V Battery cuts off while doing Motor Wizard by NiZZioN » Sun, 2022-04-24 15:31 |
1 |
by kexbox Fri, 2022-05-06 16:32 |
|
|
FSESC6,6 VESC6 version number. by alexantosh » Mon, 2021-11-22 10:34 |
1 |
by ypl Tue, 2022-02-08 21:54 |
|
|
Does the blue tooth adapter from Flipsky now work with Iphone? by Don124 » Thu, 2022-06-23 07:50 |
1 |
by oskkis Wed, 2022-08-17 18:48 |
|
|
Unidentified Part by amit_bhar » Thu, 2021-12-23 23:43 |
1 |
by skyline1970 Fri, 2021-12-24 09:22 |
|
|
Maytech VESC duty cycle & PID control problems by subodh.malgonde » Mon, 2018-10-01 11:49 |
1 |
by subodh.malgonde Tue, 2018-10-02 11:59 |
|
|
SPI encoder on MIN4 by john » Wed, 2018-11-14 11:31 |
1 |
by F4metz Sat, 2019-03-02 14:18 |
|
|
maytech mto91hbm-nh motors hal sensor by nolander » Thu, 2019-01-10 00:01 |
1 |
by sunsam8 Thu, 2019-01-10 11:15 |
|
|
Gate driver by RSR » Sat, 2019-01-26 21:46 |
1 |
by bgdwiepp Fri, 2019-03-01 15:21 |
|
|
3 shunt low side resistor configuration based on VESC 6 by jordanlow » Thu, 2019-02-14 16:42 |
1 |
by TechAUmNu Thu, 2019-02-14 18:31 |
|
|
84v VESC?? by larsrocket » Sun, 2018-04-01 22:41 |
1 |
by larsrocket Mon, 2018-04-30 19:59 |
Log in to post new content in the forum.
