You are here
VESC Original Hardware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
VESC75/300 - Does your IMU work? by Gerhard » Mon, 2021-02-08 00:15 |
4 |
by Gerhard Thu, 2021-02-25 17:39 |
|
|
Power button works only as turn ON button, but not working as turn OFF by zmei116 » Tue, 2020-05-26 18:52 |
4 |
by electricfox Sat, 2024-03-09 18:57 |
|
|
VESC6 75 - any issues? by nick.bolton » Wed, 2022-08-10 08:09 |
3 |
by nick.bolton Thu, 2022-08-18 22:14 |
|
|
Input Voltage on PPM (Servo) VESC6? by Marc Pflugmann » Fri, 2018-05-25 21:02 |
3 |
by Roger Wolff Thu, 2018-05-31 08:05 |
|
|
How to RC segway Ninebot pro using BALANCE mode? $$ by zmei116 » Sun, 2020-02-23 12:22 |
3 |
by zmei116 Fri, 2020-12-04 00:36 |
|
|
Vesc repair guidances by Booya » Tue, 2020-03-10 17:31 |
3 |
by oschlueter Fri, 2021-09-10 12:10 |
|
|
Why Mosfet and Motor HW temp sensor schematic are different?! by ThierryGTLTS » Sat, 2017-09-09 10:13 |
3 |
by ThierryGTLTS Mon, 2017-09-11 12:50 |
|
|
What is ADC3 used for in VESC6 by Tilman Baumann » Tue, 2018-04-10 11:12 |
3 |
by Gos1 Mon, 2023-06-26 13:56 |
|
|
75/300 Layout or gerbers by Chapel81 » Fri, 2020-08-28 21:27 |
3 |
by Chapel81 Wed, 2020-09-09 16:24 |
|
|
VESC 75/300 Frying in BLDC Regen by ezonca » Fri, 2020-10-23 21:53 |
3 |
by TechAUmNu Thu, 2020-10-29 13:43 |
|
|
Danger to go more than 100% duty cycle during downhill ? by f.damien12 » Thu, 2022-03-24 14:12 |
3 |
by skyline1970 Sat, 2022-03-26 09:29 |
|
|
Hub motor e-bike not recognized by olivierskypullc... » Tue, 2019-04-16 11:06 |
3 |
by Ampit Fri, 2023-09-29 12:38 |
|
|
Spare 5V current for accessories by Pimousse » Mon, 2018-01-08 15:49 |
3 |
by benjamin Wed, 2018-01-24 15:21 |
|
|
75/300 NRF Pairing by eptv » Sat, 2019-10-12 14:47 |
3 |
by frank Thu, 2019-12-05 11:22 |
|
|
Built in BLE HD60 not Working by CS » Mon, 2021-08-23 13:21 |
3 |
by frank Thu, 2021-08-26 08:09 |
|
|
Why does the 75/300 have VCC at 3.4V? by TechAUmNu » Tue, 2020-03-31 14:01 |
3 |
by TechAUmNu Wed, 2020-09-02 12:04 |
|
|
Vesc 6 MKIV ? by mchatain » Mon, 2020-05-04 11:43 |
3 |
by maxpla Wed, 2020-06-10 10:04 |
|
|
WAND -Joystick faulty- by chris_winkel » Wed, 2022-03-23 17:53 |
2 |
by chris_winkel Mon, 2022-03-28 11:14 |
|
|
Temperature Sensor Dallas DS18B20 by tobiokanobi » Tue, 2022-06-07 10:07 |
2 |
by tobiokanobi Wed, 2022-06-08 15:25 |
|
|
Controlling multiple VESC over SPI by ttufuor » Mon, 2019-11-18 04:37 |
2 |
by Danny Bokma Fri, 2020-01-24 18:29 |
|
|
Hooking up two or more motor drivers to the same MCU by darkclaude » Thu, 2019-06-20 10:02 |
2 |
by skyline1970 Wed, 2019-07-31 13:53 |
|
|
Need advice : repair , vesc 4.12, vesc 6.4 or wait ? by frameto » Mon, 2017-11-20 21:57 |
2 |
by frameto Wed, 2017-11-22 22:01 |
|
|
VESC 4.12 - Data loss on power off by da_rul0r » Wed, 2019-08-14 16:43 |
2 |
by da_rul0r Thu, 2019-08-15 08:33 |
|
|
fault_code_high_offset_current_sensor_1 by Enak » Thu, 2019-10-10 02:48 |
2 |
by Enak Fri, 2019-10-11 01:24 |
|
|
HW 4.12 USB Device Descriptor Failed-> Red light flashed on start by MTBVASEY » Wed, 2018-04-04 11:06 |
2 |
by MTBVASEY Wed, 2018-04-04 22:24 |
Log in to post new content in the forum.
