You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
motor max rpm and current severely limited? by Roy Zhang » Mon, 2021-08-09 19:23 |
2 |
by vadicus Thu, 2021-08-12 04:06 |
|
|
Overheating protection, voltage-/current-limitation etc. by kianK » Thu, 2021-04-15 07:23 |
2 |
by lilliamhoyle Wed, 2021-07-07 09:36 |
|
|
FAILED DETCTION. REASON:-11,and FAULT_CODE_DRV by marco esteban l... » Wed, 2019-12-11 01:40 |
2 |
by marco esteban l... Wed, 2019-12-11 18:54 |
|
|
PPM Configuration is Only Working While Connected to VESC Software by kyle45 » Wed, 2020-01-15 05:13 |
2 |
by frank Mon, 2020-01-27 21:03 |
|
|
Servo Control PPM by jonthie » Tue, 2020-01-28 15:04 |
2 |
by IanG Thu, 2020-04-16 11:42 |
|
|
Speed control by dent » Tue, 2020-03-10 20:11 |
2 |
by dent Wed, 2020-03-11 02:49 |
|
|
Possible to use a e-scooter brake as a Gas lever? by max1102 » Fri, 2019-11-08 07:59 |
2 |
by max1102 Mon, 2019-11-18 21:25 |
|
|
VESC Tool Crashing on connection (on Macbook version) by svelte.ca » Thu, 2025-07-31 00:00 |
2 |
by etavav Thu, 2025-09-18 17:19 |
|
|
RT Data, v3.01, Amazon Fire Tablet (sideloaded) by j.konrad » Thu, 2022-02-24 14:51 |
2 |
by j.konrad Fri, 2022-02-25 14:14 |
|
|
Hall sensor problems by Traceo » Wed, 2021-11-10 00:05 |
2 |
by Traceo Fri, 2021-11-19 22:35 |
|
|
beginners by viniii00 » Tue, 2021-11-23 20:12 |
2 |
by FOURDAN Mon, 2022-07-04 10:13 |
|
|
Duty Cycle Mode - limited ZERO RPM duty cycle by maheshK » Mon, 2021-11-29 11:24 |
2 |
by frank Tue, 2021-11-30 07:46 |
|
|
Android & usb by TONY61 » Mon, 2025-02-10 12:48 |
2 |
by TONY61 Wed, 2025-02-12 14:54 |
|
|
Vesc Tool Mobile can't update Vesc Firmware by Happy Giraffe » Wed, 2022-01-19 21:48 |
2 |
by Happy Giraffe Thu, 2022-01-20 23:50 |
|
|
FOC with 2 Poles and only 6 Windings? by martin2day » Fri, 2020-07-17 08:16 |
2 |
by martin2day Sat, 2020-07-18 10:36 |
|
|
48v problems by vufmihai » Wed, 2020-07-22 22:53 |
2 |
by vufmihai Fri, 2020-07-31 07:25 |
|
|
Setup for very slow < 100RPM on Maytech 6365 Motor. by jason3w » Tue, 2020-09-01 10:52 |
2 |
by asapereira Mon, 2020-09-14 10:26 |
|
|
VESC Tool Platinum : Windows 7 - Not working by moorem » Mon, 2020-05-18 23:19 |
2 |
by thefallen Tue, 2020-12-15 12:06 |
|
|
Android environment. by ka_ru » Tue, 2020-10-20 13:47 |
2 |
by ka_ru Wed, 2020-10-21 10:54 |
|
|
Switch between different modes via remote by Cledus » Sun, 2017-10-22 13:56 |
2 |
by MatwoSvK Tue, 2017-11-07 22:32 |
|
|
Vesctool otg by meashman » Sat, 2022-08-06 10:05 |
2 |
by meashman Wed, 2022-08-17 06:39 |
|
|
FOC configuration when resistance is measured as R=0. by Roger Wolff » Tue, 2018-08-28 18:20 |
2 |
by Foxyirish1987 Tue, 2020-04-07 13:12 |
|
|
PPM read has an offset by tuloski » Thu, 2018-09-13 09:38 |
2 |
by Stupidspencer Fri, 2019-07-19 03:09 |
|
|
VESC tool "GUI" issue. by Roger Wolff » Tue, 2018-01-02 15:13 |
2 |
by ThierryGTLTS Wed, 2018-01-10 17:38 |
|
|
VESC tool and sk8-esc V6 set up shows incorrectcurrent usage by DominykasS » Fri, 2022-09-30 13:54 |
2 |
by Frizzaper Wed, 2023-11-15 04:25 |
Log in to post new content in the forum.
