You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Setup for very slow < 100RPM on Maytech 6365 Motor. by jason3w » Tue, 2020-09-01 10:52 |
2 |
by asapereira Mon, 2020-09-14 10:26 |
|
|
VESC Tool Platinum : Windows 7 - Not working by moorem » Mon, 2020-05-18 23:19 |
2 |
by TheFallen Tue, 2020-12-15 12:06 |
|
|
Writing value to both VESCs on FocFox Unity by agraham » Wed, 2022-02-23 21:45 |
2 |
by benjamin Thu, 2022-02-24 10:57 |
|
|
Calibration ERROR with TLE5012B Magnetic encoder in ABI mode by cejota » Fri, 2022-03-25 03:19 |
2 |
by XieMaster Mon, 2022-11-14 05:32 |
|
|
Writing to slave vesc sometimes cause loss of can bus by meashman » Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
|
|
[SOLVED] RPM setting not working by olivierskypullc... » Wed, 2019-02-27 12:14 |
2 |
by olivierskypullc... Wed, 2019-03-06 10:10 |
|
|
Vesc Tool not opening on windows computer by maccert » Sat, 2019-03-02 11:04 |
2 |
by Luca Torani Sun, 2019-03-03 20:32 |
|
|
Is it possible to stop a motor at one exact desired location without hall sensor? by vimi94 » Thu, 2019-08-15 10:58 |
2 |
by vimi94 Tue, 2019-08-20 13:37 |
|
|
BEMF plot not working with VESC6 by ESCam » Tue, 2019-03-12 21:29 |
2 |
by ESCam Tue, 2019-03-19 18:03 |
|
|
How to Traction Control VESC 6 by Karl » Thu, 2018-10-11 03:33 |
2 |
by marti Wed, 2018-10-17 06:02 |
|
|
Voltage measurement calibration? by pyryjansson » Tue, 2019-04-30 20:19 |
2 |
by frank Wed, 2022-11-30 09:55 |
|
|
load cell data logging by magnus.w » Thu, 2019-05-02 00:21 |
2 |
by Tom Burton Wed, 2019-11-06 16:43 |
|
|
Wrong HW version selected during FW update by babyboi » Sat, 2018-12-15 21:30 |
2 |
by babyboi Sat, 2018-12-22 03:55 |
|
|
VESC tool for windows by djevIen » Mon, 2019-06-17 08:02 |
2 |
by frank Fri, 2022-06-03 21:33 |
|
|
Vesc Tool on Carplay - We need a display! by modman » Tue, 2023-03-28 16:10 |
2 |
by wraven Fri, 2024-06-21 16:18 |
|
|
Understanding FOC Wizard Innerworkings by gravity99 » Thu, 2022-08-18 22:24 |
2 |
by gravity99 Mon, 2022-08-22 15:23 |
|
|
"CAN bus support is not enabled in this build of VESC Tool" by hdfghdfgh » Wed, 2023-04-26 16:13 |
2 |
by mansi712 Mon, 2024-10-28 12:19 |
|
|
Cannot connect win10 tried everything I have read by meziked » Wed, 2025-07-02 00:45 |
2 |
by meziked Wed, 2025-07-02 16:21 |
|
|
Detection failed. Reason: Flux linkage detection failed by Donnyten » Sun, 2022-10-09 20:31 |
2 |
by Donnyten Tue, 2022-10-11 02:56 |
|
|
Battery Voltage Settings by huffauden19 » Wed, 2020-03-04 23:17 |
2 |
by laser30 Sat, 2021-03-13 16:57 |
|
|
BUG - RAMPING on VESC TOOL? by Filcas » Tue, 2019-12-10 19:29 |
2 |
by Filcas Wed, 2019-12-11 17:15 |
|
|
Vesc tool 1.26.. issue with firmware updates? by beetbocks » Tue, 2019-12-17 10:17 |
2 |
by Stupidspencer Wed, 2019-12-25 23:04 |
|
|
motor detection - what to expect when spinning up the motor by grantmoy74 » Sat, 2019-12-28 11:58 |
2 |
by grantmoy74 Sun, 2019-12-29 05:21 |
|
|
How to update VESC Tool? by Heimfried » Wed, 2020-02-05 10:35 |
2 |
by marialoise Fri, 2020-03-13 20:20 |
|
|
I Mac Vesc tool !!!! by PHATTY » Fri, 2019-10-11 17:56 |
2 |
by Bender Wed, 2021-03-10 14:39 |
Log in to post new content in the forum.
