You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
ADC and arrow input dont work by stefann » Wed, 2019-10-09 18:51 |
0 |
by stefann Wed, 2019-10-09 20:04 |
|
|
s for second S for siemens by maxxximatoze » Mon, 2019-10-07 12:22 |
0 |
by maxxximatoze Mon, 2019-10-07 12:22 |
|
|
VESC Tool returns bad ERPM value by karololo » Thu, 2019-10-03 10:12 |
1 |
by TechAUmNu Fri, 2019-10-04 15:05 |
|
|
I need VESC Tool Version 1.13, please. by Astropower » Sun, 2019-09-08 18:22 |
1 |
by thewho Wed, 2019-09-18 08:29 |
|
|
VESC Tool Android - Real-Time Data per controller or combined? by kamikatze13 » Sat, 2019-08-31 22:39 |
1 |
by Stupidspencer Sun, 2019-09-15 19:30 |
|
|
VESC setup in generator application by SaqibBajwa » Fri, 2018-09-21 04:28 |
14 |
by arifbustani Thu, 2019-09-12 18:54 |
|
|
VESC 4.12 - Current limited at 100A by Laerson » Sun, 2019-09-08 20:23 |
1 |
by benjamin Mon, 2019-09-09 18:20 |
|
|
I need VESC Tool Version 1.13, please. by Astropower » Sun, 2019-09-08 18:22 |
0 |
by Astropower Sun, 2019-09-08 18:22 |
|
|
ERPM scaling / Maximum motor speed / RPM by Azza » Tue, 2019-09-03 17:16 |
1 |
by Azza Fri, 2019-09-06 18:20 |
|
|
UART Safety Feature by jaghori.sasan » Wed, 2019-09-04 18:45 |
0 |
by jaghori.sasan Wed, 2019-09-04 18:45 |
|
|
vesc tool crashing on 29aug19 - website down/link? by ianp » Fri, 2019-08-30 04:10 |
1 |
by frank Mon, 2019-09-02 11:26 |
|
|
Incorrect parameter detection by macieksz@pro.onet.pl » Fri, 2019-08-30 16:05 |
0 |
by macieksz@pro.onet.pl Fri, 2019-08-30 16:05 |
|
|
Is it possible to stop a motor at one exact desired location without hall sensor? by vimi94 » Thu, 2019-08-15 10:58 |
2 |
by vimi94 Tue, 2019-08-20 13:37 |
|
|
Wrong Motor detection values after STM swap dual vesc 6 by Micro » Sun, 2019-08-18 01:59 |
0 |
by Micro Sun, 2019-08-18 02:14 |
|
|
How Can I make the tool work with FW 3.5 instead of just 3.58? by ipbyrne » Fri, 2019-07-26 18:20 |
3 |
by frank Wed, 2019-08-14 14:01 |
|
|
Help setting up dual vesc via CANBUS by Jaystro16 » Sun, 2019-08-04 01:39 |
1 |
by frank Wed, 2019-08-14 13:55 |
|
|
"bad detection result received" impossible to achieved motor detection ! by titimomotete » Wed, 2019-03-20 17:21 |
2 |
by doom Mon, 2019-08-05 10:52 |
|
|
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed » Fri, 2019-08-02 20:00 |
0 |
by Munkyheed Fri, 2019-08-02 20:00 |
|
|
Changing Output Voltage frequency by davbams » Wed, 2019-07-24 21:20 |
1 |
by district9prawn Thu, 2019-07-25 02:59 |
|
|
port manufator name for windows by Ackmaniac » Thu, 2017-09-07 22:58 |
1 |
by Lindsaymarshall Tue, 2019-07-23 18:22 |
|
|
From where can I access the FOC code? by vimi94 » Mon, 2019-07-01 14:36 |
1 |
by Teslafly Sat, 2019-07-20 10:31 |
|
|
PPM read has an offset by tuloski » Thu, 2018-09-13 09:38 |
2 |
by Stupidspencer Fri, 2019-07-19 03:09 |
|
|
Fault Codes by Joe_Lowtech » Wed, 2019-02-13 20:06 |
2 |
by mthielvoldt Thu, 2019-07-18 00:38 |
|
|
Parametre for Low RPM Limit by ilan248@gmail.com » Wed, 2019-07-10 11:01 |
1 |
by askker Thu, 2019-07-11 05:04 |
|
|
cant connect via usb by curtm » Wed, 2019-06-19 03:05 |
2 |
by curtm Thu, 2019-07-04 00:37 |
Log in to post new content in the forum.
