You are here

VESC Tool

Topic / Topic starter Replies Last postsort descending
Normal topic Vesc tool mobile for raspbian
by Idoff » Sat, 2019-03-30 19:24
0
by Idoff
Sat, 2019-03-30 19:24
Normal topic How to activate e-brake on e-scooter with the throttle
by Donatas Sukelis » Sat, 2019-04-27 10:09
0
by Donatas Sukelis
Sat, 2019-04-27 10:09
Normal topic Multiple VESC's in duty cycle mode
by Rudolf10000 » Sat, 2019-04-20 13:24
1
by Rudolf10000
Mon, 2019-04-29 19:34
Normal topic How to control motor using VESC tool in computer at constant rpm?
by vimi94 » Wed, 2019-05-01 12:56
0
by vimi94
Wed, 2019-05-01 12:56
Normal topic Voltage measurement calibration?
by pyryjansson » Tue, 2019-04-30 20:19
0
by pyryjansson
Fri, 2019-05-03 23:27
Normal topic VESC Tool Error
by Geir Henriksen » Fri, 2019-05-10 14:55
1
by Geir Henriksen
Fri, 2019-05-10 15:18
Normal topic ADC Positive and Negative Ramping Time - not working
by Astropower » Tue, 2019-05-28 22:41
0
by Astropower
Tue, 2019-05-28 22:41
Normal topic UART write read arduino
by matiller » Sat, 2019-06-01 20:18
0
by matiller
Sat, 2019-06-01 20:18
Normal topic cant connect via usb
by curtm » Wed, 2019-06-19 03:05
2
by curtm
Thu, 2019-07-04 00:37
Normal topic Parametre for Low RPM Limit
by ilan248@gmail.com » Wed, 2019-07-10 11:01
1
by askker
Thu, 2019-07-11 05:04
Normal topic Fault Codes
by Joe_Lowtech » Wed, 2019-02-13 20:06
2
by mthielvoldt
Thu, 2019-07-18 00:38
Normal topic PPM read has an offset
by tuloski » Thu, 2018-09-13 09:38
2
by Stupidspencer
Fri, 2019-07-19 03:09
Normal topic From where can I access the FOC code?
by vimi94 » Mon, 2019-07-01 14:36
1
by Teslafly
Sat, 2019-07-20 10:31
Normal topic port manufator name for windows
by Ackmaniac » Thu, 2017-09-07 22:58
1
by Lindsaymarshall
Tue, 2019-07-23 18:22
Normal topic Changing Output Voltage frequency
by davbams » Wed, 2019-07-24 21:20
1
by district9prawn
Thu, 2019-07-25 02:59
Normal topic Can I re-use an old Galaxy S3 to run the VESC tool?
by Munkyheed » Fri, 2019-08-02 20:00
0
by Munkyheed
Fri, 2019-08-02 20:00
Normal topic "bad detection result received" impossible to achieved motor detection !
by titimomotete » Wed, 2019-03-20 17:21
2
by doom
Mon, 2019-08-05 10:52
Normal topic Help setting up dual vesc via CANBUS
by Jaystro16 » Sun, 2019-08-04 01:39
1
by frank
Wed, 2019-08-14 13:55
Normal topic How Can I make the tool work with FW 3.5 instead of just 3.58?
by ipbyrne » Fri, 2019-07-26 18:20
3
by frank
Wed, 2019-08-14 14:01
Normal topic Wrong Motor detection values after STM swap dual vesc 6
by Micro » Sun, 2019-08-18 01:59
0
by Micro
Sun, 2019-08-18 02:14
Normal topic Is it possible to stop a motor at one exact desired location without hall sensor?
by vimi94 » Thu, 2019-08-15 10:58
2
by vimi94
Tue, 2019-08-20 13:37
Normal topic Incorrect parameter detection
by macieksz@pro.onet.pl » Fri, 2019-08-30 16:05
0
by macieksz@pro.onet.pl
Fri, 2019-08-30 16:05
Normal topic vesc tool crashing on 29aug19 - website down/link?
by ianp » Fri, 2019-08-30 04:10
1
by frank
Mon, 2019-09-02 11:26
Normal topic UART Safety Feature
by jaghori.sasan » Wed, 2019-09-04 18:45
0
by jaghori.sasan
Wed, 2019-09-04 18:45
Normal topic ERPM scaling / Maximum motor speed / RPM
by Azza » Tue, 2019-09-03 17:16
1
by Azza
Fri, 2019-09-06 18:20
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - VESC Tool