You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Use sensors on the output shaft of a motor attached to a large gear ratio gearbox by davidq1688 » Wed, 2022-04-27 05:23 |
1 |
by tobiokanobi Thu, 2022-04-28 14:48 |
|
Vesc doesn't react to can messages from PC by BorisDeroo » Fri, 2021-12-17 16:54 |
1 |
by yuri12 Wed, 2022-02-09 17:33 |
|
inconsistent behavior after motor control using FOC by alexantosh » Wed, 2022-01-05 10:24 |
1 |
by frank Wed, 2022-01-05 11:21 |
|
Vesc Tool For Mac by kmfpod » Tue, 2022-06-14 22:06 |
1 |
by frank Wed, 2022-06-15 09:58 |
|
Pictures from "Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller"? by timmertens » Thu, 2022-06-16 17:56 |
1 |
by frank Thu, 2022-06-16 19:47 |
|
Taking 5-6 seconds for running motor under ADC mode by asnamp » Fri, 2022-06-24 13:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:24 |
|
Cannot connect to vesc tool app by sharpshooterjd » Fri, 2022-07-29 23:39 |
1 |
by skyline1970 Sun, 2022-11-27 16:38 |
|
FOC detection needs load? by tuloski » Thu, 2018-09-13 10:19 |
1 |
by TechAUmNu Thu, 2018-09-13 12:26 |
|
build VESC Tool on Linux Mint by cb » Fri, 2018-04-13 16:19 |
1 |
by benjamin Mon, 2018-04-16 10:59 |
|
Motor Poles by Enak » Fri, 2017-09-08 00:57 |
1 |
by ThierryGTLTS Fri, 2017-09-08 09:01 |
|
bugreport. Scale useless by Roger Wolff » Wed, 2017-11-29 12:24 |
1 |
by Svenska Svenson Mon, 2017-12-04 07:56 |
|
Determining Motor and Battery Current Max by technique » Tue, 2020-07-14 15:03 |
1 |
by probie Wed, 2020-08-26 22:01 |
|
How to set dead time on BLDC mode? by AllenFF » Wed, 2020-04-15 05:48 |
1 |
by hexakopter Sat, 2020-04-18 16:30 |
|
[SOLVED] Compile vesc tool mobile apk by TZTZ » Mon, 2020-05-25 18:51 |
1 |
by TZTZ Mon, 2020-05-25 23:14 |
|
flux linkage detection failled by Clsprinkler@aol.com » Tue, 2020-10-20 03:02 |
1 |
by Kent Tabor Wed, 2020-10-21 04:36 |
|
PPM problems by rufr123 » Sat, 2020-10-31 20:49 |
1 |
by TheFallen Tue, 2020-11-03 00:29 |
|
Bug Report - Motor/App Data not saved to VESC by bb67 » Sun, 2020-06-21 10:26 |
1 |
by bb67 Sat, 2020-07-04 12:21 |
|
Position control without encoder by bearing » Tue, 2023-04-04 18:45 |
1 |
by bearing Thu, 2023-04-06 22:07 |
|
Sailboat regen by flydr2 » Wed, 2023-04-12 20:10 |
1 |
by vadicus Wed, 2023-05-10 20:06 |
|
Problem to configure my esc with PWM-signal by Lucar » Wed, 2022-09-14 10:05 |
1 |
by skyline1970 Thu, 2022-11-24 20:26 |
|
PPM Pulselength mapping by Shaftdriver » Tue, 2022-10-04 19:50 |
1 |
by skyline1970 Thu, 2022-11-24 20:15 |
|
Vesc Tool on Carplay - We need a display! by modman » Tue, 2023-03-28 16:10 |
1 |
by frank Wed, 2023-03-29 16:12 |
|
VESC Tool Error by Geir Henriksen » Fri, 2019-05-10 14:55 |
1 |
by Geir Henriksen Fri, 2019-05-10 15:18 |
|
From where can I access the FOC code? by vimi94 » Mon, 2019-07-01 14:36 |
1 |
by Teslafly Sat, 2019-07-20 10:31 |
|
Vesc tool Update... by getinthebag » Sun, 2019-03-03 00:41 |
1 |
by mustafa Sun, 2019-11-10 21:10 |
Log in to post new content in the forum.