You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Question about custom coding to shutdown the motor by dsuresh » Fri, 2021-04-30 18:51 |
2 |
by dsuresh Sun, 2021-05-02 23:41 |
|
VESC 4.12 FW5.02 CAN status messages is spamming bus, external controller, SOLVED: NEEDED INIT! by Offline » Mon, 2021-05-03 14:57 |
1 |
by Offline Tue, 2021-05-04 10:03 |
|
AC Synchronous motor support by Dark » Mon, 2019-07-29 15:03 |
5 |
by rizanirusli Wed, 2021-05-05 08:39 |
|
Help rc car bldc configuration vesc 4.20 by Katt » Sun, 2021-04-18 15:25 |
2 |
by spacewalker Tue, 2021-05-11 13:01 |
|
Minimum speed push cart using arduino by BarBumble » Wed, 2021-05-12 09:29 |
0 |
by BarBumble Wed, 2021-05-12 09:29 |
|
Custom code changes- I/O pin go high or low by dsuresh » Thu, 2021-05-13 19:50 |
2 |
by dsuresh Fri, 2021-05-14 22:30 |
|
Compatibility with BiSS-C absolute encoder by wisllayvitrio » Sat, 2021-05-15 23:39 |
0 |
by wisllayvitrio Sat, 2021-05-15 23:40 |
|
Battery to motor voltage by fazekas » Sat, 2021-05-15 16:03 |
2 |
by fazekas Sun, 2021-05-16 20:43 |
|
mxus xf15 thermistor by ligi » Tue, 2021-05-18 09:43 |
0 |
by ligi Tue, 2021-05-18 09:43 |
|
BLDC zero cross happens too early by Sgw32 » Thu, 2021-05-20 19:10 |
0 |
by Sgw32 Thu, 2021-05-20 19:10 |
|
Integration of VESC with a display using I2C by dsuresh » Thu, 2021-05-20 19:32 |
0 |
by dsuresh Thu, 2021-05-20 19:32 |
|
VESCTool - connect to ESP32? by SimonR_SFX » Thu, 2021-05-06 11:26 |
1 |
by danilolattaro Fri, 2021-05-21 23:38 |
|
IPM parameter adjust by rbargallo » Sun, 2021-05-23 22:43 |
0 |
by rbargallo Sun, 2021-05-23 22:43 |
|
BIG Flash/Spark!!!!! New 100v/250a :-( by Fpvlee » Thu, 2021-05-13 03:17 |
4 |
by Fpvlee Tue, 2021-05-25 00:12 |
|
Update FW on multiple VESC pcbs using CAN issue by Offline » Wed, 2021-05-19 15:07 |
2 |
by Offline Wed, 2021-05-26 08:23 |
|
difference between VSEC GOLD, Silver, Bronze by roeebloch » Sun, 2021-04-18 19:43 |
2 |
by frank Wed, 2021-05-26 11:04 |
|
Using an on/off throttle by Evwan » Mon, 2021-05-24 16:59 |
1 |
by SamuL Wed, 2021-05-26 12:52 |
|
Direct drive wheel ac servo+vesc by adilrepas » Wed, 2021-05-26 12:50 |
0 |
by adilrepas Wed, 2021-05-26 12:58 |
|
VESC PAS sensor connection, which pins? by matajumotors » Fri, 2021-05-28 12:37 |
0 |
by matajumotors Fri, 2021-05-28 12:37 |
|
General question on tuning vesc by stevo11811 » Wed, 2021-06-02 05:06 |
0 |
by stevo11811 Wed, 2021-06-02 05:12 |
|
Trampa VESC6 USB connectivity problem caused by usb hub? by hagoston » Tue, 2021-06-01 10:27 |
4 |
by hagoston Wed, 2021-06-02 09:27 |
|
IMU and ADC1/2 not working by Dwal » Wed, 2021-05-26 18:05 |
2 |
by Dwal Thu, 2021-06-03 22:34 |
|
Regen on the positive side of the throttle curve? by kcswimrac » Fri, 2021-06-04 22:09 |
1 |
by vadicus Fri, 2021-06-04 22:51 |
|
Regen wiring Help Pls by Fpvlee » Fri, 2021-06-04 23:44 |
2 |
by frank Sun, 2021-06-06 11:48 |
|
Runaway on throttle disconnection by DavidBike » Sat, 2021-06-05 15:44 |
3 |
by vadicus Sun, 2021-06-06 22:11 |
Log in to post new content in the forum.