Hi,
Does anyone know how I can reduce the time delay from forward to reverse operation? I guess it has something to do with a "max erpm before full brake" parameter, but I cannot find
this setting in the android Vesc Tool.
I am using vesc6 with firmware 5.1 on an electric boat. To configure, I use android Vesc Tool 2.06.
Hi everybody,
I recently connected the hall sensors of my 26 inch wheel hub motor to my flysky VESC 6.6 (12S, 60A) .
The result is a way smoother with no more "failure" in the acceleration. But the acceleration itself is much slower than with sensorless mounting.
Do you have any idea of which settings I could change to get the maximum acceleration allowed by my motor ?
Sincerly
Hello,
I have a small Tablet PC with Windows 10 32-Bit on it (Odys Prime Win 10). When I try to open the VESC Tool 3.00 this Message comes: "This app can't run on your PC".
I doesn't open when i use Admin rights nor does ist open under Windows 7 or 8. I have deactivated Windows Smartscreen and the Firewall, that didn't work also.
I have check following Programs:
OpenGL Version 4.4
OpenCL Version 1.2
Microsoft DirectX Runtime-Version 12
what could the problem be?
Best Regards,
Android VESC Tool downloaded from Play Store.
Lacroix Lonestar Supersport.
The stormcore showed up in the list of paired devices for a while but I wasn't getting the app to work correctly (I'm new so sure it was operator error). I deleted the entry for the stormcore in the list of paired devices and at that time I didn't know I should unpair it. I assumed deleting it would unpair it. I am not getting this message when I try to connect to the stormcore:
Hello all,
I am new to the platform and have just started configuring my engine. About the setup engine FOC this was also correctly detected and ran properly. In the FOC settings of the engine settings I wanted to test again RL, which also worked. However, when testing the engine flux linkage, the engine starts first and then blocks abruptly.
What could be the reason for this?
Do I have to adjust another setting?
The motor polarity is actually automatically detected, or am I wrong?
Hey,
I am using VESC paired with an electric motor in order to control a propeller that will be implemented in a small aircraft.
I am wondering if it is possible to have some type of set up or configuration using PPM or other type of control APP, that allows for controlling the position of the motor.
Hi all
I have 10 VESC 4.12 connected via CAN bus
I can get and set settings on all of them, using VESC tool, and CAN forward feature.
When I want to update I have first downloaded newest bootloader on all of them using the usb cable
After that I conencted to one of them using USB, went to the Firmware tab, selecting my custom firmware.
I select the update ALL button, I can see the LED on all of the pcb's are flashing like sparkling..
Then its done, and I reset the power
problems;
1) vesc tool dus not recognize second (CAN) vesc
2) motors not starting equal.
3) not able to connect to second vesc
video about problem; https://youtu.be/0If_Vksw65c
i now that both te motors work correctly.
Hello,
we´re trying to build a speedometer over CAN massages.
We set the CAN Baud to 100K and the CAN Mode to Comm Bridge but our CAN analyser only reads Errors.
Is there a setting mistake?
If there is an easier way to build such a speedometer with RPM, please let me know. ;)
We´re using an VESC 6 MK 4.
THX
Hi,
I'm setting to up communication to teh VESC through an Arduino. Using SolidGeek's libraries, I have been able to send position control commands. What I need, is to read in the current position of the motor.
In order to set position, I modified the existing "setRPM" to make a "setPOS" command.
To set position, I naively tired to convert "getVescValues" to a "getVescPos", with the command value of "COMM_ROTOR_POSITION". But this does not seem to be recognized (payload size is zero).
