You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Trouble Detecting ABI Encoder on VESC6/75 by jonathansel on Fri, 2022-10-07 22:34 |
by jonathansel Fri, 2022-10-07 22:34 |
General discussion | ||
|
VESC 6.6 vs. MK5 vs. MK6 by jejaj25773 on Sat, 2024-07-27 02:37 |
by jejaj25773 Sat, 2024-07-27 02:37 |
General discussion | ||
|
Input Setup Wizard Does Not Ask if Single or Multi VESC by kylemuramatsu on Wed, 2019-03-13 03:22 |
1 |
by benjamin Wed, 2019-03-13 09:38 |
General discussion | |
|
Can i change the controller (LQFP64) with (LQFP100) with same Firmware? by GalihRiddle on Thu, 2019-09-05 13:44 |
2 |
by GalihRiddle Mon, 2019-09-09 13:22 |
General discussion | |
|
bootloader destroied by notger on Tue, 2017-09-19 19:55 |
3 |
by dinamee Sat, 2018-01-13 10:09 |
General discussion | |
|
Control via UART and connect to VESC Tool using BLE by Seudo on Sun, 2023-12-17 21:34 |
1 |
by vadicus Thu, 2024-01-11 23:00 |
General discussion | |
|
PPM Position over CAN bus? by walleywalker on Thu, 2021-12-02 18:47 |
by walleywalker Thu, 2021-12-02 18:47 |
General discussion | ||
|
Minimum speed push cart using arduino by BarBumble on Wed, 2021-05-12 09:29 |
by BarBumble Wed, 2021-05-12 09:29 |
General discussion | ||
|
starting current/torque with speed controller by nomada on Thu, 2023-11-30 12:20 |
by nomada Thu, 2023-11-30 12:20 |
General discussion | ||
|
9 by RoopeKuisma on Sun, 2020-05-10 21:58 |
by RoopeKuisma Sun, 2020-05-10 21:58 |
General discussion | ||
|
Regenerative braking question and vesc input question by asaf123098 on Sat, 2019-06-15 09:55 |
2 |
by asaf123098 Sun, 2019-06-16 00:23 |
General discussion | |
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker on Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
General discussion | |
|
VESC in-air startup failure by jschall on Sat, 2025-04-26 00:56 |
2 |
by jschall Sat, 2025-04-26 01:32 |
General discussion | |
|
Nunchuck app working for anyone? by Pedrodemio on Sat, 2018-02-10 04:11 |
1 |
by Pedrodemio Sun, 2018-02-11 01:00 |
General discussion | |
|
UAVCAN vs DroneCAN vs Cypal by AndreasSkaar on Fri, 2024-05-03 22:17 |
4 |
by Williamzoe2002 Thu, 2025-03-20 10:23 |
General discussion | |
|
Cannot downgrade from 5.03 to 5.02 by kallep on Sat, 2022-02-26 19:08 |
5 |
by frank Sat, 2022-03-12 12:09 |
General discussion | |
|
Open ESC for sensored 1/12 pan cars? by DocTrucker on Tue, 2022-08-02 08:33 |
1 |
by skyline1970 Thu, 2022-11-24 21:02 |
General discussion | |
|
Noob here by Nothanks on Sat, 2024-04-20 01:21 |
by Nothanks Sat, 2024-04-20 01:21 |
General discussion | ||
|
Making master and slave motors communicate both ways by Sis7 on Tue, 2020-07-21 05:58 |
by Sis7 Tue, 2020-07-21 05:58 |
General discussion | ||
|
Motor draws current (up to 120 A), but doesn't turn by Heimfried on Sun, 2020-03-01 22:21 |
by Heimfried Sun, 2020-03-01 22:21 |
General discussion |
Pages
