You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
VESC minimum RPM by askker on Thu, 2019-07-11 05:03 |
6 |
by Artius Reynolds Sun, 2020-10-18 23:25 |
General discussion | |
builtin ble on vesc 75_300 by alexefoil on Wed, 2019-07-03 02:35 |
6 |
by Glennisoty Thu, 2021-04-15 05:31 |
VESC Original Hardware | |
Torque control with PWM at 10kHz for LinuxCNC + MESA + AC servo by antonchromjak on Tue, 2018-03-06 08:01 |
6 |
by Artabotak Sat, 2024-01-06 09:24 |
General discussion | |
is Cross Coupling power limitation? by ziumus on Sat, 2021-02-06 15:57 |
6 |
by ziumus Sat, 2021-02-27 16:08 |
General discussion | |
VESC TOOL ADC Voltage mapping too low. SOLVED by Ecyclist on Fri, 2018-10-19 22:38 |
5 |
by sam.vanratt Thu, 2018-11-22 20:21 |
General discussion | |
what is the best vesc For long-term sea observation by jhgjg on Thu, 2022-09-22 12:12 |
5 |
by frank Mon, 2022-09-26 15:44 |
General discussion | |
experiment tab rpm ramp up and dual separate motor control by tobiokanobi on Thu, 2022-04-14 20:20 |
5 |
by tobiokanobi Tue, 2022-04-26 15:32 |
VESC Tool | |
trampa by badger1666 on Mon, 2017-12-11 22:37 |
5 |
by wdaehn Wed, 2017-12-13 12:17 |
General discussion | |
Problem to start bldc in vesc tool vesc-mini4 esc by uav-orion on Wed, 2019-06-12 16:18 |
5 |
by uav-orion Wed, 2019-06-19 21:50 |
General discussion | |
I can't get my fresc to work I think all the leds are lighting up but when I pull the trigger on the remote nothing happens by pdxcjc on Fri, 2022-03-11 17:46 |
5 |
by Gatze Mon, 2022-05-09 17:03 |
Third Party Hardware | |
75100 ESC Hardware and firmware open source by ypl on Tue, 2022-02-08 16:21 |
5 |
by Artabotak Tue, 2024-04-16 20:36 |
Third Party Hardware | |
VESC - custom board by st0r on Wed, 2023-03-08 12:21 |
5 |
by st0r Sat, 2023-04-01 01:51 |
General discussion | |
missing Analog Throttle failsafe by bosko on Thu, 2019-12-05 16:47 |
5 |
by bosko Fri, 2019-12-06 13:25 |
General discussion | |
Range not showing accurately by th3jonathan on Tue, 2022-05-24 17:43 |
5 |
by frank Mon, 2022-05-30 07:53 |
General discussion | |
AC Synchronous motor support by Dark on Mon, 2019-07-29 15:03 |
5 |
by rizanirusli Wed, 2021-05-05 08:39 |
General discussion | |
3 sensorless motors connected with belt by moose09876 on Wed, 2022-09-14 23:26 |
5 |
by moose09876 Fri, 2022-09-16 14:09 |
General discussion | |
HW4.12 with FW 3.27, FOC OK, BLDC problems. by ThierryGTLTS on Thu, 2017-09-07 11:14 |
5 |
by ThierryGTLTS Sat, 2017-09-16 18:45 |
VESC Tool | |
nice solution 3x3 phase VESC out to 3 single motor wires by tobiokanobi on Tue, 2022-04-19 17:13 |
5 |
by tobiokanobi Mon, 2022-04-25 14:55 |
VESC Original Hardware | |
Holding torque in "Duty Cycle" mode by Petja on Mon, 2020-01-13 01:19 |
5 |
by pf26 Wed, 2020-03-04 08:58 |
General discussion | |
Kill Function - Analogue Input by austrobots on Sat, 2022-12-10 12:19 |
5 |
by austrobots Tue, 2022-12-13 04:51 |
General discussion |