You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
VESC design specification, manual by velolac on Thu, 2020-01-02 15:54 |
1 |
by velolac Sat, 2020-01-11 00:05 |
VESC Original Hardware | |
|
VESC 6 Schematic Question by mendez on Tue, 2019-02-12 07:11 |
8 |
by frank Thu, 2019-12-05 11:28 |
VESC Original Hardware | |
|
75/300 NRF Pairing by eptv on Sat, 2019-10-12 14:47 |
3 |
by frank Thu, 2019-12-05 11:22 |
VESC Original Hardware | |
|
Driving two motors with 75/300 by cmarc on Wed, 2019-10-16 17:32 |
1 |
by benjamin Fri, 2019-10-18 10:37 |
VESC Original Hardware | |
|
VESC 4.12 Duty is always 110%. Possible short? by tahirali1 on Sun, 2019-10-13 14:22 |
by tahirali1 Sun, 2019-10-13 14:22 |
VESC Original Hardware | ||
|
fault_code_high_offset_current_sensor_1 by Enak on Thu, 2019-10-10 02:48 |
2 |
by Enak Fri, 2019-10-11 01:24 |
VESC Original Hardware | |
|
VESC 75/300 current noise / losing sync? by ezonca on Thu, 2019-10-03 23:06 |
2 |
by benjamin Thu, 2019-10-10 07:56 |
VESC Original Hardware | |
|
VESC 4.12 - Data loss on power off by da_rul0r on Wed, 2019-08-14 16:43 |
2 |
by da_rul0r Thu, 2019-08-15 08:33 |
VESC Original Hardware | |
|
Hooking up two or more motor drivers to the same MCU by darkclaude on Thu, 2019-06-20 10:02 |
2 |
by skyline1970 Wed, 2019-07-31 13:53 |
VESC Original Hardware | |
|
VESC Hardware by eschroff on Thu, 2019-07-25 02:38 |
1 |
by skyline1970 Wed, 2019-07-31 13:35 |
VESC Original Hardware | |
|
Programming Vesc 4.12 motor spin only in detection mode by DanieleRA on Sun, 2019-07-28 16:29 |
by DanieleRA Sun, 2019-07-28 16:29 |
VESC Original Hardware | ||
|
dual VESC battery current by chris_winkel on Tue, 2019-06-18 15:26 |
by chris_winkel Tue, 2019-06-18 15:26 |
VESC Original Hardware | ||
|
How exactly do I connect a VESC 6.4 to an Arduino Nano? by MaxMaker1 on Tue, 2018-07-03 23:18 |
5 |
by molak Tue, 2019-06-04 19:39 |
VESC Original Hardware | |
|
Fault: FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 on VESC 6 by Jackl on Tue, 2019-05-28 14:48 |
by Jackl Tue, 2019-05-28 14:48 |
VESC Original Hardware | ||
|
Servomotor control with VESC6 by Humberto Estrada on Wed, 2019-05-22 16:15 |
by Humberto Estrada Wed, 2019-05-22 16:15 |
VESC Original Hardware | ||
|
Trampa boards online store by jrowe on Tue, 2019-04-16 06:28 |
by jrowe Tue, 2019-04-16 06:28 |
VESC Original Hardware | ||
|
Inductance (L) measurement by rahmaev_a_o on Tue, 2018-08-07 10:10 |
4 |
by benjamin Sat, 2019-02-23 10:11 |
VESC Original Hardware | |
|
VESC on 48V 1500W HUB motor by jordanlow on Sat, 2019-01-12 14:52 |
4 |
by jordanlow Thu, 2019-01-24 04:14 |
VESC Original Hardware | |
|
Flashing via SWD works, but no green LED or USB enumeration by vpl on Fri, 2018-11-16 17:48 |
1 |
by vpl Wed, 2018-11-21 17:27 |
VESC Original Hardware | |
|
Using ABI Encoders by danielw on Tue, 2018-10-30 14:33 |
1 |
by danielw Wed, 2018-11-07 15:38 |
VESC Original Hardware |
Pages
