You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Multiple VESCs, CANBus, Galvanic Isolation and Puffs of Smoke by KirkusMaximus on Wed, 2023-01-18 00:55 |
1 |
by frank Wed, 2023-01-18 12:29 |
General discussion | |
|
Questions about encoder on FSesc 6 by willyfan on Wed, 2018-08-29 20:30 |
11 |
by Vedderfanboy Tue, 2023-01-17 13:17 |
General discussion | |
|
5.02 Firmware on Trampa VESC 6 MKVI? by maxhertz on Sun, 2023-01-15 13:58 |
2 |
by maxhertz Mon, 2023-01-16 00:24 |
General discussion | |
|
Brake lever Cutoff switch seperate from Regen braking/throttle wheel by SuperSpeed Scooter on Thu, 2022-11-03 19:13 |
2 |
by oangelo Wed, 2023-01-11 12:25 |
General discussion | |
|
Fault Code Look Up Table (for CSV, Excel or Similar) by JayCee on Wed, 2023-01-11 04:26 |
by JayCee Wed, 2023-01-11 04:26 |
General discussion | ||
|
motors wont turn by Jambi56 on Mon, 2022-09-26 01:48 |
2 |
by Zander rowley Mon, 2023-01-09 16:43 |
General discussion | |
|
Bldc generator voltage control by Gsorter on Fri, 2022-12-09 23:52 |
3 |
by frank Wed, 2023-01-04 18:39 |
General discussion | |
|
Help i have no idea how it works... by Xtracker133 on Sat, 2022-12-31 14:55 |
2 |
by Xtracker133 Tue, 2023-01-03 22:52 |
General discussion | |
|
Recommended method for CAN Bus communication for 3 VESC by sivanhere on Sun, 2023-01-01 12:09 |
by sivanhere Sun, 2023-01-01 12:09 |
General discussion | ||
|
How to implement a simple autopilot by oangelo on Thu, 2022-12-22 12:50 |
by oangelo Thu, 2022-12-22 12:50 |
General discussion | ||
|
Need help with brushed fc 24 bolt motor control by searth on Sun, 2022-12-18 16:05 |
by searth Sun, 2022-12-18 16:05 |
General discussion | ||
|
Field weakening and MTPA by Gsorter on Fri, 2022-12-16 21:54 |
2 |
by Gsorter Sun, 2022-12-18 02:20 |
General discussion | |
|
Impact of motor resistance value vs temperature by Torbjorn on Fri, 2022-12-16 09:09 |
by Torbjorn Fri, 2022-12-16 09:09 |
General discussion | ||
|
Dangerous bug when using KILLSWITCH and PPM, FW5.03 by corgon on Wed, 2022-12-14 16:37 |
2 |
by corgon Thu, 2022-12-15 23:10 |
General discussion | |
|
Setting PID gains (and other config parameters) over CAN Bus by TheCuriousRobot on Thu, 2022-12-15 22:03 |
by TheCuriousRobot Thu, 2022-12-15 22:03 |
General discussion | ||
|
Powering VESC and motor from powersupply by SIGURD on Tue, 2022-12-13 13:53 |
3 |
by frank Thu, 2022-12-15 20:34 |
General discussion | |
|
VESC and T500 Thruster - Problems obtaining right speed by SIGURD on Tue, 2022-12-13 13:45 |
2 |
by SIGURD Wed, 2022-12-14 16:20 |
General discussion | |
|
How to avoid engine overheating? by oangelo on Thu, 2022-12-08 23:03 |
3 |
by vadicus Tue, 2022-12-13 22:39 |
General discussion | |
|
Connection issues using PyVESC by axelray on Tue, 2022-12-13 15:15 |
by axelray Tue, 2022-12-13 15:15 |
General discussion | ||
|
Help needed please by Mark griffin on Tue, 2022-12-13 14:51 |
by Mark griffin Tue, 2022-12-13 14:51 |
General discussion |
Pages
