You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
VESC Not Functioning with Magnetic or Quadrature Encoders by privvyledge on Wed, 2023-05-24 16:59 |
1 |
by electricfox Thu, 2023-05-25 21:10 |
General discussion | |
|
Alternate for STM32F405 Microcontroller by gowrav on Fri, 2021-06-18 07:44 |
6 |
by damien31 Wed, 2023-05-24 13:01 |
General discussion | |
|
Cogging issue with ADC input by Mitsuru Fujii on Mon, 2023-05-22 14:45 |
1 |
by frank Tue, 2023-05-23 16:43 |
General discussion | |
|
4wd rover using hub-motors by mhyer on Thu, 2023-05-18 09:56 |
2 |
by velolac Tue, 2023-05-23 10:03 |
General discussion | |
|
3 speed switch by de-bodgery on Sat, 2021-08-21 02:22 |
17 |
by Oscar Lozano Gimenez Mon, 2023-05-22 14:07 |
General discussion | |
|
static torque control by wjpremerlani on Sun, 2023-05-14 13:52 |
4 |
by wjpremerlani Sat, 2023-05-20 12:23 |
General discussion | |
|
Motor is "pumping" under load in current control mode. is this normal? by etienne on Sat, 2023-05-13 17:16 |
2 |
by iv.kravchenko Sat, 2023-05-20 08:31 |
General discussion | |
|
VESC 100/250 missing hall sensor plug by steve1428 on Sat, 2023-04-08 10:00 |
1 |
by iv.kravchenko Fri, 2023-05-19 22:26 |
General discussion | |
|
vesc app (iphone) brushed motor setting. by outrunner on Tue, 2023-05-16 22:49 |
1 |
by outrunner Wed, 2023-05-17 00:28 |
General discussion | |
|
Configuration via CAN? by mrPalomar on Tue, 2023-05-16 02:22 |
by mrPalomar Tue, 2023-05-16 02:22 |
General discussion | ||
|
Shutdown mode by Akeela23 on Sat, 2023-05-06 01:50 |
1 |
by Akeela23 Sat, 2023-05-06 01:56 |
General discussion | |
|
just receaved my awesome new vesc 6 plus however it wont configurate i get an errot message. :( by sabladask on Wed, 2023-05-03 16:15 |
2 |
by frank Fri, 2023-05-05 20:54 |
General discussion | |
|
DUAL VESC FOR BIDIRECTIONAL ROTATION by Khaliduzzaman Mredul on Fri, 2023-05-05 06:46 |
by Khaliduzzaman Mredul Fri, 2023-05-05 11:00 |
General discussion | ||
|
[SOLVED] PWM speed control at low RPM by comes04 on Sun, 2023-04-16 13:30 |
1 |
by comes04 Wed, 2023-05-03 20:44 |
General discussion | |
|
[SOLVED, was a mistake] Set ERPM command: issue with the speed controller with higher speed values that is possible with bat vol by yes_wecangogreen on Wed, 2023-04-12 00:51 |
1 |
by yes_wecangogreen Sat, 2023-04-29 09:24 |
General discussion | |
|
Bench Testing by usaevo7 on Tue, 2023-04-25 16:50 |
by usaevo7 Tue, 2023-04-25 16:50 |
General discussion | ||
|
Vesc for 5000kW QS 205 Hub Motor ebike by Amiran on Fri, 2019-09-27 15:52 |
10 |
by vadicus Sun, 2023-04-23 01:23 |
General discussion | |
|
VESC6 with DRV8320 by cromoly on Wed, 2023-04-19 02:40 |
by cromoly Wed, 2023-04-19 02:40 |
General discussion | ||
|
How does controlling two different motors over CAN bus really work? by oangelo on Sat, 2023-04-15 20:05 |
by oangelo Sat, 2023-04-15 20:05 |
General discussion | ||
|
HFI Mode Hoverboard Hub Motor by JulianT on Wed, 2023-04-12 19:16 |
by JulianT Sat, 2023-04-15 11:09 |
General discussion |
Pages
