You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Wand firmware 1.3 by peacue » Mon, 2021-11-22 09:59 |
1 |
by frank Mon, 2021-11-22 12:56 |
|
|
re-scaling CAN setDUTY CYCLE to -1 to 1 instead of 0 to 1 by a.dahhak » Fri, 2020-03-06 11:09 |
1 |
by a.dahhak Mon, 2020-03-09 10:38 |
|
|
How Update firmware vesc 6.41 with broken micro USB fw 3.40? by adrian210188 » Thu, 2020-03-12 01:18 |
1 |
by Pimousse Sat, 2020-03-21 13:01 |
|
|
UAVCAN v0 actuator message features by Henrik1 » Sat, 2020-03-14 19:00 |
1 |
by goocare Tue, 2020-03-24 10:15 |
|
|
VESC6 current and duty cycle scale problem? by henry10210 » Sun, 2020-03-29 22:34 |
1 |
by mansi712 Tue, 2024-10-01 12:48 |
|
|
Spin the motor and stop at a set tachometer index by jchillerup » Tue, 2019-12-10 12:29 |
1 |
by frank Wed, 2019-12-11 14:51 |
|
|
MK3 branch in bldc repo? by henry10210 » Tue, 2019-12-31 23:49 |
1 |
by Teslafly Thu, 2020-02-06 21:22 |
|
|
Fw 4.01 potential issue by Joeshaw » Sun, 2020-03-01 23:15 |
1 |
by Pimousse Sat, 2020-03-21 13:10 |
|
|
FAULT_CODE_UNDER_VOLTAGE corrupted by edilger » Mon, 2024-06-17 13:13 |
1 |
by edilger Sat, 2024-06-22 17:45 |
|
|
Version 6+ make arm_sdk_install failing by trtr6842 » Mon, 2024-07-01 02:03 |
1 |
by onid Sat, 2024-07-13 11:21 |
|
|
Limiting of throttle curves has no effect by Ackmaniac » Thu, 2017-09-07 17:21 |
1 |
by frank Tue, 2017-09-19 09:35 |
|
|
Cant find firmware by Rad07 » Sun, 2024-09-15 01:05 |
1 |
by Sharkboy Sat, 2024-09-21 23:47 |
|
|
adding PAS feature on Firmware 5.01 by marc426 » Sat, 2023-07-15 23:56 |
1 |
by marc426 Sun, 2023-07-16 15:25 |
|
|
Firmware 3.29 hardware 4.12 , 0.5mOhm shunts by brushlessdevil » Sun, 2017-10-15 19:28 |
1 |
by benjamin Thu, 2017-10-19 15:15 |
|
|
Most reliable control of VESC? by ProgramThyself » Wed, 2023-10-11 06:29 |
1 |
by vadicus Thu, 2023-10-12 03:13 |
|
|
STM32F405RGTx LQFP64 .ioc file by gyongyoj » Fri, 2023-10-27 14:21 |
1 |
by nyc Mon, 2023-11-20 08:25 |
|
|
[Contributing][FOC] injected ADC and code clarity by Guillaume227 » Fri, 2017-12-15 18:00 |
1 |
by Roger Wolff Sat, 2017-12-16 13:21 |
|
|
VESC 6.0 Hardware Shows Up As HW 410 in VESC-Tool by FWachter » Thu, 2017-12-21 20:51 |
1 |
by wdaehn Fri, 2017-12-22 08:22 |
|
|
How much SRAM and Flash memory is needed to run the latest VESC firmware/software? by WackoKacko » Mon, 2023-02-06 14:22 |
1 |
by moshangliu Wed, 2024-06-26 17:33 |
|
|
BLDC switching frequency by tuloski » Wed, 2018-09-19 13:18 |
1 |
by bauck Tue, 2020-11-17 17:08 |
|
|
Will voltage offset on phase cause tracking to get wrong position? by TechAUmNu » Wed, 2018-01-17 18:14 |
1 |
by TechAUmNu Wed, 2018-01-17 21:42 |
|
|
Hall sensor detection failed (AWD setup) by frameto » Tue, 2018-10-02 22:02 |
1 |
by ronmotor Tue, 2020-10-27 02:20 |
|
|
firmware 6.05 beta by Trebor77 » Sun, 2024-04-07 10:19 |
1 |
by yoodog Sat, 2024-09-28 23:26 |
|
|
firmware too old! by ad_brad » Sun, 2018-10-14 18:33 |
1 |
by arvidb Sun, 2018-10-14 19:21 |
|
|
VESC Control over NRF by Christian » Tue, 2018-03-27 14:42 |
1 |
by m.juan Wed, 2018-07-04 13:44 |
Log in to post new content in the forum.
