You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
How to activate e-brake on e-scooter with the throttle by Donatas Sukelis » Sat, 2019-04-27 10:09 |
0 |
by Donatas Sukelis Sat, 2019-04-27 10:09 |
|
Connecting ABI encoder to VESC by Gas_Sn4ke » Mon, 2018-11-26 06:00 |
0 |
by Gas_Sn4ke Mon, 2018-11-26 06:00 |
|
Problem with encoder readings with arduino by ruthvikchanda » Thu, 2018-12-06 07:06 |
0 |
by ruthvikchanda Thu, 2018-12-06 07:06 |
|
ADC Positive and Negative Ramping Time - not working by Astropower » Tue, 2019-05-28 22:41 |
0 |
by Astropower Tue, 2019-05-28 22:41 |
|
Lisp scripting questions/suggestions/remarks by Gatze » Sun, 2022-04-24 12:13 |
0 |
by Gatze Sun, 2022-04-24 13:00 |
|
Error on log-file recording: Could not get Positioning Working by hpb66 » Mon, 2022-05-23 08:23 |
0 |
by hpb66 Mon, 2022-05-23 08:23 |
|
questions about "RUN DETECTION" by yuri12 » Thu, 2022-01-20 04:30 |
0 |
by yuri12 Thu, 2022-01-20 04:30 |
|
The engine stopped spinning after updating firmware by brian adilman » Wed, 2022-01-26 17:40 |
0 |
by brian adilman Wed, 2022-01-26 19:15 |
|
NRF connection error by Denn » Wed, 2022-02-02 11:17 |
0 |
by Denn Wed, 2022-02-02 11:17 |
|
Throttle Input reading not changing by niko_la » Fri, 2022-07-22 02:40 |
0 |
by niko_la Fri, 2022-07-22 02:40 |
|
Different rpm when using 3 vesc with can-bus by ewakegermanyhq » Wed, 2022-08-03 17:03 |
0 |
by ewakegermanyhq Wed, 2022-08-03 17:03 |
|
Upgrade the Bootloader? by erikfed » Tue, 2022-03-08 20:32 |
0 |
by erikfed Tue, 2022-03-08 20:32 |
|
getting started by SilkyD » Mon, 2021-10-25 12:49 |
0 |
by SilkyD Mon, 2021-10-25 12:49 |
|
Acceleration Temperature Decrease (Relevant Safety Update) by frank » Sun, 2017-10-29 22:19 |
0 |
by frank Sun, 2017-10-29 22:19 |
|
Vesc_tool OVER_TEMP_FET by XIII » Thu, 2018-01-11 17:26 |
0 |
by XIII Thu, 2018-01-11 17:26 |
|
Changing minimum duty cycle prevents VESC from connecting via USB while ADC throttle is connected by shimdidly » Sun, 2017-10-15 00:48 |
0 |
by shimdidly Sun, 2017-10-15 00:48 |
|
FSESC seems to be speed limiting my motor by 5amsung4 » Sat, 2022-09-03 18:50 |
0 |
by 5amsung4 Mon, 2022-09-05 07:51 |
|
arrow key hot working (neither on the app) but the board works correclty by lorenzidomenico94 » Tue, 2020-01-14 11:30 |
0 |
by lorenzidomenico94 Tue, 2020-01-14 11:30 |
|
"CAN bus support is not enabled in this build of VESC Tool" by hdfghdfgh » Wed, 2023-04-26 16:13 |
0 |
by hdfghdfgh Wed, 2023-04-26 16:13 |
|
Help i can not setup my motors by jakson01 » Fri, 2022-09-09 18:37 |
0 |
by jakson01 Fri, 2022-09-09 18:37 |
|
VESC tool load empty by arminoonk » Thu, 2020-01-16 14:51 |
0 |
by arminoonk Thu, 2020-01-16 14:51 |
|
Battery set up by Sandro luis » Thu, 2024-04-18 15:55 |
0 |
by Sandro luis Thu, 2024-04-18 15:55 |
|
FOC Encoder autotune issue by David_Lo » Tue, 2020-01-21 11:54 |
0 |
by David_Lo Tue, 2020-01-21 11:54 |
|
sick srm50 absolute encoder, I don't know how to configure it by Davidson SIlvei... » Mon, 2024-04-22 21:45 |
0 |
by Davidson SIlvei... Mon, 2024-04-22 21:45 |
|
HFI plot by Rick van der Sloot » Sun, 2022-10-02 22:26 |
0 |
by Rick van der Sloot Sun, 2022-10-02 22:26 |
Log in to post new content in the forum.