You are here
VESC Tool
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
Battery Voltage Settings by huffauden19 » Wed, 2020-03-04 23:17 |
2 |
by laser30 Sat, 2021-03-13 16:57 |
|
|
Been at it for like 14 hours... HALP by mnchvgs79 » Wed, 2021-03-03 22:03 |
4 |
by TheFallen Sun, 2021-03-07 15:25 |
|
|
BEMF plot not working with VESC6 by ESCam » Tue, 2019-03-12 21:29 |
2 |
by ESCam Tue, 2019-03-19 18:03 |
|
|
Benchmark regenerative braking by diggis » Fri, 2021-02-19 10:01 |
0 |
by diggis Fri, 2021-02-19 10:01 |
|
|
benjamin, New feature please by justinlinh » Sat, 2020-07-11 00:06 |
3 |
by justinlinh Sat, 2020-07-11 01:42 |
|
|
bidirectional joystick conrol with saparate brake switch by Erik fijlstra » Thu, 2024-05-16 16:02 |
2 |
by Erik fijlstra Mon, 2024-08-05 16:39 |
|
|
bluetooth connection issue by hicklinc » Thu, 2020-10-08 14:17 |
0 |
by hicklinc Thu, 2020-10-08 14:17 |
|
|
Bluetooth connection possible with METR device? by Cuprani » Sun, 2018-04-01 23:00 |
1 |
by Pimousse Wed, 2018-04-04 11:34 |
|
|
Bluetooth RX/TX by eastcoastkiter » Fri, 2019-06-28 19:02 |
5 |
by radler Sat, 2020-06-20 17:06 |
|
|
brake switch/brake regen question by smallbikefun » Sat, 2024-04-06 01:48 |
2 |
by smallbikefun Sun, 2024-04-14 22:08 |
|
|
BUG - RAMPING on VESC TOOL? by Filcas » Tue, 2019-12-10 19:29 |
2 |
by Filcas Wed, 2019-12-11 17:15 |
|
|
Bug Report - Motor/App Data not saved to VESC by bb67 » Sun, 2020-06-21 10:26 |
1 |
by bb67 Sat, 2020-07-04 12:21 |
|
|
bugreport. Scale useless by Roger Wolff » Wed, 2017-11-29 12:24 |
1 |
by Svenska Svenson Mon, 2017-12-04 07:56 |
|
|
build VESC Tool on Linux Mint by cb » Fri, 2018-04-13 16:19 |
1 |
by benjamin Mon, 2018-04-16 10:59 |
|
|
Calibration ERROR with TLE5012B Magnetic encoder in ABI mode by cejota » Fri, 2022-03-25 03:19 |
2 |
by XieMaster Mon, 2022-11-14 05:32 |
|
|
CAN bus support not enabled in this build of vesc tool? by Tsomo » Fri, 2021-10-01 09:48 |
18 |
by merten Fri, 2024-08-09 18:14 |
|
|
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed » Fri, 2019-08-02 20:00 |
0 |
by Munkyheed Fri, 2019-08-02 20:00 |
|
|
Can I run duty sweep without laptop? by gavinremme » Tue, 2024-07-30 00:05 |
0 |
by gavinremme Tue, 2024-07-30 00:05 |
|
|
Can the PPM mapping be changed so that higher duty cycle means slower speed? by UncleJoe » Mon, 2020-05-25 11:46 |
3 |
by UncleJoe Thu, 2020-11-19 15:06 |
|
|
Can't find good parameters for FOC detection by Kabroc » Thu, 2020-04-30 16:28 |
0 |
by Kabroc Thu, 2020-04-30 16:28 |
|
|
Can't get Dual drive/CAN bus working by Xadiant » Sun, 2019-09-22 20:49 |
11 |
by Kokonenen Wed, 2023-04-19 11:10 |
|
|
Can't spin both motors over CAN-bus by Kokonenen » Wed, 2023-04-19 11:19 |
3 |
by Kokonenen Fri, 2023-04-21 09:18 |
|
|
Can't update the VESC firmware by mansolander » Thu, 2020-03-05 11:30 |
1 |
by mansolander Fri, 2020-03-06 11:24 |
|
|
Cannot connect to vesc tool app by sharpshooterjd » Fri, 2022-07-29 23:39 |
1 |
by skyline1970 Sun, 2022-11-27 16:38 |
|
|
Cannot get any PPM signals from Arduino. Or is it just the VESC tool? by MaxMaker1 » Thu, 2018-06-21 23:06 |
4 |
by tuloski Thu, 2018-09-13 09:36 |
Log in to post new content in the forum.
