You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Реверс вращения двигателя by Wolod5 » Sat, 2021-01-16 09:59 |
2 |
by Wolod5 Sat, 2021-01-16 12:21 |
|
|
Custom Battery Settings? Inaccurate Wh readings? by dfelz » Wed, 2020-04-08 02:04 |
3 |
by starset Wed, 2021-01-13 22:54 |
|
|
FOC detection not working, "L=0" by chundri » Tue, 2021-01-12 15:02 |
2 |
by chundri Wed, 2021-01-13 15:40 |
|
|
motor to slow and no power by Thiery Vardon » Sat, 2021-01-09 10:45 |
2 |
by Thiery Vardon Tue, 2021-01-12 13:27 |
|
|
VESC 75/300 Configuration problems with Hacker Q80 Motors by electricfox » Thu, 2019-02-28 18:23 |
13 |
by Cherry Tue, 2021-01-12 11:56 |
|
|
How do I compile the VESC Tool? by ipbyrne » Wed, 2019-07-24 16:58 |
4 |
by a.dahhak Fri, 2021-01-01 15:25 |
|
|
Trasmitter not able to communicate with VESC by Andrea » Thu, 2020-03-26 20:22 |
1 |
by TheFallen Mon, 2020-12-28 16:16 |
|
|
VESC 75/300 Configuration of 7kg Innerrunner Surron by electricfox » Thu, 2019-05-16 18:38 |
15 |
by Armond Ohan Mon, 2020-12-21 06:34 |
|
|
VESC Tool Platinum : Windows 7 - Not working by moorem » Mon, 2020-05-18 23:19 |
2 |
by TheFallen Tue, 2020-12-15 12:06 |
|
|
one motor spinning faster than the other? by jon218white » Mon, 2020-12-14 22:57 |
0 |
by jon218white Mon, 2020-12-14 22:57 |
|
|
Vesc 6, FW 5.1, WH charged is not being logged by BalorNG » Thu, 2020-12-03 14:19 |
0 |
by BalorNG Thu, 2020-12-03 14:19 |
|
|
Updated Firmware on 2 New VESC's says firmware doesnt match when connected by CanBus Cable by vesserik » Mon, 2019-04-08 21:10 |
1 |
by dbell Tue, 2020-12-01 02:14 |
|
|
Maximum possible Baudrate in UART? by nlabs » Sun, 2018-04-08 01:52 |
5 |
by anttok Tue, 2020-12-01 00:26 |
|
|
Motors wont turn independently by huffauden19 » Mon, 2020-11-30 06:24 |
0 |
by huffauden19 Mon, 2020-11-30 06:24 |
|
|
Write App Configuration via UART [SOLVED] by v8-rt » Mon, 2020-11-02 13:13 |
1 |
by Halas1941 Sun, 2020-11-29 14:04 |
|
|
Ac synchronous motor support by Yksbs » Mon, 2020-08-24 07:14 |
1 |
by skyline1970 Sat, 2020-11-21 11:11 |
|
|
vesc UART with arduino 33 BLE by amaussa » Mon, 2020-10-12 16:57 |
2 |
by Seb44120 Fri, 2020-11-20 23:06 |
|
|
Can the PPM mapping be changed so that higher duty cycle means slower speed? by UncleJoe » Mon, 2020-05-25 11:46 |
3 |
by UncleJoe Thu, 2020-11-19 15:06 |
|
|
Android version doesn't find serial. by ka_ru » Thu, 2020-11-19 09:13 |
0 |
by ka_ru Thu, 2020-11-19 09:13 |
|
|
ESC State, Switch Value, and Motor Position unknown by 175_pilot » Wed, 2020-11-04 04:22 |
0 |
by 175_pilot Wed, 2020-11-04 04:22 |
|
|
PPM problems by rufr123 » Sat, 2020-10-31 20:49 |
1 |
by TheFallen Tue, 2020-11-03 00:29 |
|
|
ennoid bms by roqm » Fri, 2020-10-30 18:22 |
0 |
by roqm Fri, 2020-10-30 18:22 |
|
|
Terminal Command for Current? by Mannerow » Thu, 2020-10-29 23:07 |
0 |
by Mannerow Thu, 2020-10-29 23:07 |
|
|
PPM Mapping's VESC Tool not working by cornballs » Sun, 2019-09-22 09:17 |
1 |
by clistpdx Sat, 2020-10-24 02:40 |
|
|
How to determine motor size in wizard, hub motors ? by Photolad61 » Mon, 2019-03-25 19:43 |
1 |
by Kent Tabor Fri, 2020-10-23 22:29 |
Log in to post new content in the forum.
