You are here

General discussion

Topic / Topic starter Replies Last postsort descending
Normal topic Building the vesc firmware in Chibi Studio
by chris1seto » Sat, 2019-01-12 02:36
1
by kinzma
Thu, 2019-02-14 09:42
Normal topic No connection with vesc
by Matthieu van Ra... » Wed, 2019-02-13 18:07
8
by sam.vanratt
Thu, 2019-02-14 15:33
Normal topic 2 vs 3 phase shunts
by antonchromjak » Sun, 2018-04-15 13:25
13
by TechAUmNu
Fri, 2019-02-15 18:57
Normal topic Struggling in startup BLDC in sensorless mode
by dangminhducnbk » Fri, 2019-02-15 03:42
2
by dangminhducnbk
Sun, 2019-02-17 12:48
Normal topic Observer tracking fail
by dangminhducnbk » Sun, 2019-02-17 14:09
0
by dangminhducnbk
Sun, 2019-02-17 14:09
Normal topic information to drive 400kv drone motor on ClosedLoop with AS5047
by Syl2078 » Sun, 2019-02-17 19:20
0
by Syl2078
Sun, 2019-02-17 19:20
Normal topic VESC Questions from the newbie
by mendez » Fri, 2019-02-08 21:13
10
by frank
Mon, 2019-02-18 08:52
Normal topic VESC on DIY CNC router
by tbartoletta » Wed, 2019-02-20 03:00
5
by GunnarW
Thu, 2019-02-21 16:44
Normal topic Current sensor and commanded current
by galp » Fri, 2019-02-22 23:08
0
by galp
Fri, 2019-02-22 23:08
Normal topic BLDC vs FOC mode, motor‘s spin direction is invert
by moto_guy » Wed, 2019-02-20 11:48
4
by moto_guy
Sun, 2019-02-24 09:11
Normal topic Flipsky6.6 usb not detected
This topic has been moved to "Third Party Hardware" (View topic)
Normal topic When I mount the propeller on the motor ,I get a new promblem
by moto_guy » Sat, 2019-03-02 05:16
0
by moto_guy
Sat, 2019-03-02 05:16
Normal topic Win10 BLE Error
by jzy1115 » Tue, 2018-04-17 16:20
1
by spei
Mon, 2019-03-04 13:55
Normal topic Brushless or brushed motor for autonomous rc-car
by Joe_Lowtech » Thu, 2018-12-20 11:56
4
by Joe_Lowtech
Tue, 2019-03-05 11:00
Normal topic VESC6 PCB questions
by ESCam » Sat, 2018-12-29 00:17
6
by TechAUmNu
Thu, 2019-03-07 11:28
Normal topic Pedelec/eBike, PAS and sensors
by sam.vanratt » Mon, 2018-11-19 11:46
2
by sam.vanratt
Thu, 2019-03-07 20:22
Normal topic C80100 Outrunner 50kv does not want to spin.
by Wormsnake » Sun, 2019-03-03 10:30
1
by TheFallen
Sun, 2019-03-10 17:54
Normal topic VESC regenerating while RPM increased
by olivierskypullc... » Fri, 2019-03-08 16:32
2
by olivierskypullc...
Mon, 2019-03-11 10:45
Normal topic ADC pin voltage not zero
by zoppp » Fri, 2019-02-08 23:44
12
by zoppp
Tue, 2019-03-12 01:17
Normal topic how do you arm your Vesc in arduino code?
by the creator » Wed, 2019-03-13 01:11
0
by the creator
Wed, 2019-03-13 01:33
Normal topic Input Setup Wizard Does Not Ask if Single or Multi VESC
by kylemuramatsu » Wed, 2019-03-13 03:22
1
by benjamin
Wed, 2019-03-13 09:38
Normal topic Fault finding on failed VESC
This topic has been moved to "Third Party Hardware" (View topic)
Normal topic Can I change control mode on the fly through the UART port?
by spork » Wed, 2019-03-13 02:24
2
by spork
Wed, 2019-03-13 15:41
Normal topic DRV8323
by Jessica » Thu, 2019-03-14 11:41
0
by Jessica
Thu, 2019-03-14 11:42
Normal topic Guide for modifying firmware/ apps
by Enak » Wed, 2017-09-06 17:24
3
by TechAUmNu
Thu, 2019-03-14 17:38
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - General discussion