You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Controlling Servo via VESC and PPM by bruchpilot123 » Wed, 2020-09-23 13:26 |
1 |
by jarryc Sun, 2021-05-02 01:25 |
|
|
Can someone please post the steps to do position control from vesc tool? by dp » Wed, 2022-02-16 14:51 |
1 |
by frank Wed, 2022-02-16 17:24 |
|
|
ADC Brake while stand , not parking brake by spacewalker » Tue, 2021-07-27 08:09 |
1 |
by skyline1970 Sat, 2021-09-18 11:42 |
|
|
status message by riku » Thu, 2022-11-17 05:31 |
1 |
by frank Thu, 2022-11-17 17:55 |
|
|
Motor Controller + Motor + Lecture by AlexSTM32 » Fri, 2022-09-30 19:29 |
1 |
by frank Sat, 2022-10-01 15:37 |
|
|
Dual Motor Software "Limited Slip" Differential by luky » Thu, 2021-06-10 10:43 |
1 |
by frank Thu, 2021-06-10 11:07 |
|
|
Vibrations under hard regen by gecko242 » Fri, 2022-10-07 15:03 |
1 |
by frank Fri, 2022-10-07 15:30 |
|
|
UAV motor BLDC detection fails by Torbjorn » Wed, 2022-10-12 13:54 |
1 |
by frank Wed, 2022-10-12 17:04 |
|
|
Slot car ESC? by adrianblakey » Thu, 2022-10-13 11:52 |
1 |
by frank Thu, 2022-10-13 14:49 |
|
|
FSESC 4.2 Firmware Resetting by Pranay » Fri, 2021-08-27 12:18 |
1 |
by TechAUmNu Fri, 2021-08-27 17:20 |
|
|
Problem with motor spin in Foc with encoder mode by kdomanski » Thu, 2021-06-17 21:55 |
1 |
by kdomanski Fri, 2021-06-18 15:28 |
|
|
Inconsistant braking force when full brake starting to apply by Koxx3 » Sat, 2022-10-22 16:21 |
1 |
by Koxx3 Sun, 2022-10-23 13:22 |
|
|
GPIO Pins on VESC? by phils » Sat, 2022-10-22 17:58 |
1 |
by frank Sat, 2022-10-22 20:37 |
|
|
Motor parameters constantly changing. by Alistair Goodman » Tue, 2022-09-06 15:57 |
1 |
by Alistair Goodman Wed, 2022-09-07 10:04 |
|
|
Encoder position resetting to 0° by Michelle90 » Tue, 2022-10-25 18:55 |
1 |
by GijsB Sun, 2022-10-30 20:17 |
|
|
Current controller issue - Glitches at low current, low RPM by GijsB » Sun, 2022-10-30 12:59 |
1 |
by GijsB Sun, 2022-10-30 15:37 |
|
|
Arduino and vesc integration issue by dsuresh » Thu, 2021-07-08 17:07 |
1 |
by dsuresh Thu, 2021-07-08 17:09 |
|
|
Tuning strategy for a large motor? by MrSurly » Tue, 2022-11-01 06:51 |
1 |
by vadicus Mon, 2022-11-14 18:23 |
|
|
VESCs rotating the motors at constant RPM on UART control by Pratham701 » Tue, 2021-07-13 10:49 |
1 |
by Indy8976 Wed, 2022-08-24 11:27 |
|
|
Unable to turn on Smart Reverse by EBTEAM » Wed, 2022-11-02 08:35 |
1 |
by EBTEAM Wed, 2022-11-02 12:58 |
|
|
Battery/Motor Current on VESC Tool is less than Actuals by gowrav » Thu, 2021-07-15 13:27 |
1 |
by skyline1970 Sat, 2021-09-18 11:44 |
|
|
Motor Driver Voltage Spike Problem by sersam » Sat, 2022-11-12 19:23 |
1 |
by skyline1970 Thu, 2022-11-24 20:00 |
|
|
VESC 6+ CAN bus by kimpet » Thu, 2019-04-25 13:40 |
1 |
by eguven Fri, 2021-11-12 20:50 |
|
|
High rpm issue kde3520xf by magnus.w » Fri, 2019-04-26 12:46 |
1 |
by magnus.w Sat, 2019-05-04 12:33 |
|
|
Current KP(Current controller proportional gain) by Geir Henriksen » Tue, 2019-04-30 10:51 |
1 |
by Ricardo Bosqui Tue, 2020-02-11 15:12 |
Log in to post new content in the forum.
