You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
VESC stopped working, can't connect to USB by Hyperion » Mon, 2018-04-09 16:53 |
6 |
by bloggerjaan Wed, 2020-03-11 12:31 |
|
VESC - FAULT_CODE_DRV : motor no more spinning by piepolitb » Sat, 2018-05-19 12:27 |
4 |
by seif Wed, 2020-03-11 20:12 |
|
Slow down deacceleration?? by yulaw2k » Tue, 2020-03-17 07:16 |
1 |
by vadicus Wed, 2020-03-18 16:56 |
|
HFI and braking by aethyr » Thu, 2020-03-19 21:01 |
0 |
by aethyr Thu, 2020-03-19 21:01 |
|
6 Phase Motor - How to Drive it? by vitormhenrique » Wed, 2020-02-19 05:47 |
2 |
by Badkad Fri, 2020-03-20 19:36 |
|
Understanding Kv and max RPM limit by ug79 » Fri, 2020-03-20 16:39 |
1 |
by Pimousse Sat, 2020-03-21 12:47 |
|
Trying to read and set MCCONF by Jamie42 » Tue, 2020-03-24 19:47 |
0 |
by Jamie42 Tue, 2020-03-24 19:47 |
|
Recording VESC parameters by Alexandru Ciocan » Wed, 2020-03-25 08:44 |
1 |
by Jamie42 Wed, 2020-03-25 12:24 |
|
weird FOC motor oscillations by andrii619 » Mon, 2020-03-02 20:30 |
1 |
by hichemhlm Sun, 2020-03-29 21:08 |
|
position control with gearbox by raess » Tue, 2018-09-25 23:48 |
18 |
by IanG Mon, 2020-03-30 06:44 |
|
4 fried vesc's Australia by adamclarke1985 » Tue, 2020-03-31 20:48 |
0 |
by adamclarke1985 Tue, 2020-03-31 21:24 |
|
VESC Calculator by lmochsner » Thu, 2020-04-02 05:13 |
0 |
by lmochsner Thu, 2020-04-02 05:13 |
|
Delayed start for slave motor by rsknudsen-dk » Mon, 2020-04-06 10:06 |
0 |
by rsknudsen-dk Mon, 2020-04-06 10:06 |
|
Using STM32F407 for a custom board by kapek » Mon, 2020-04-06 04:16 |
2 |
by vadicus Fri, 2020-04-10 06:31 |
|
Welding with the VESC by doomy1986 » Mon, 2020-04-13 14:38 |
0 |
by doomy1986 Mon, 2020-04-13 14:38 |
|
How to set dead time on BLDC mode? by AllenFF » Wed, 2020-04-15 03:27 |
0 |
by AllenFF Wed, 2020-04-15 03:27 |
|
Newbie Help please, Longer run time? by Bildoon » Mon, 2020-04-06 02:00 |
1 |
by linsus Thu, 2020-04-16 14:18 |
|
4 vesc motors at once? by i-make-robots » Thu, 2020-04-16 02:17 |
1 |
by hexakopter Sat, 2020-04-18 12:20 |
|
No, BLDC is not dead. by Pimousse » Wed, 2019-06-12 17:41 |
5 |
by hexakopter Sat, 2020-04-18 12:30 |
|
How to update firmware over CAN bus by andrii619 » Wed, 2020-04-15 17:47 |
1 |
by hexakopter Sat, 2020-04-18 12:56 |
|
how I can connect 4 vesc using CAN and how connect vesc to PC via CAN bus? by Chanyoung Jung » Mon, 2020-03-09 08:12 |
1 |
by hexakopter Sat, 2020-04-18 13:12 |
|
Custom VESC4 hardware - disable Regen? by ben5243 » Mon, 2020-04-13 19:48 |
1 |
by hexakopter Sat, 2020-04-18 16:51 |
|
Firmware Update = Quiet Motor? by worldmaverik » Sun, 2020-04-19 21:45 |
0 |
by worldmaverik Sun, 2020-04-19 21:45 |
|
Smoked 3 month old VESC - What did I do wrong? by cjjohnson97 » Tue, 2020-04-21 17:40 |
3 |
by cjjohnson97 Fri, 2020-04-24 21:38 |
|
Battery charging using motor inductance by eptv » Sun, 2020-04-26 07:44 |
0 |
by eptv Sun, 2020-04-26 07:44 |
Log in to post new content in the forum.