You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Electric moped self build. by Moped Mickey » Mon, 2019-10-28 18:15 |
1 |
by frank Mon, 2019-11-04 13:39 |
|
|
VESC LCD Display SPI by georgeli293 » Sun, 2024-01-14 20:06 |
1 |
by Sandro luis Thu, 2024-01-18 21:15 |
|
|
Paragliding rewinder control loop by eptv » Mon, 2019-11-04 08:20 |
1 |
by rookieatbest Fri, 2020-08-21 03:30 |
|
|
anti spark circuit by renaudbarbier » Mon, 2019-11-11 12:21 |
1 |
by frank Thu, 2019-11-28 10:01 |
|
|
/Slow/ top speed by Benrie » Fri, 2024-01-19 22:04 |
1 |
by vadicus Thu, 2024-01-25 06:55 |
|
|
Multiple questions about vesc control by Tripod6813 » Sun, 2023-10-15 20:03 |
1 |
by Tripod6813 Tue, 2023-10-17 22:33 |
|
|
FSESC 4.2 Firmware Resetting by Pranay » Fri, 2021-08-27 12:18 |
1 |
by TechAUmNu Fri, 2021-08-27 17:20 |
|
|
Problem with motor spin in Foc with encoder mode by kdomanski » Thu, 2021-06-17 21:55 |
1 |
by kdomanski Fri, 2021-06-18 15:28 |
|
|
Sensorless BLDC motor by Pelle van wijk » Sun, 2019-11-24 15:18 |
1 |
by thefallen Tue, 2019-11-26 09:25 |
|
|
What Software to plan custom VESC by Plermpel » Mon, 2019-09-30 22:16 |
1 |
by frank Tue, 2019-10-01 10:29 |
|
|
Problems with 100% throttle input by levin » Wed, 2023-11-08 08:32 |
1 |
by Frizzaper Tue, 2023-12-12 07:48 |
|
|
Overcome the deadband torque at low rpm by shulnak » Sun, 2023-07-30 22:48 |
1 |
by userk_88_vanto Fri, 2023-09-15 15:34 |
|
|
Vesc6MK3 stops responding to throttle input by idlebear » Fri, 2023-11-17 17:41 |
1 |
by idlebear Fri, 2023-12-29 22:44 |
|
|
BT module and UART remote simultaneously on dual vescs by Rc 44 » Fri, 2023-12-01 18:40 |
1 |
by Rc 44 Mon, 2024-01-08 04:48 |
|
|
Could not read motor configuration during detection by siegele1 » Wed, 2023-08-02 17:17 |
1 |
by electricfox Thu, 2023-08-03 08:23 |
|
|
Flipsky 75200 Pro V2.0 by sweendog311 » Fri, 2023-12-08 20:12 |
1 |
by moose09876 Thu, 2024-01-04 15:18 |
|
|
Get values from slave VESC by Snabelost » Mon, 2023-08-07 08:54 |
1 |
by Snabelost Mon, 2023-08-07 13:21 |
|
|
VESCs rotating the motors at constant RPM on UART control by Pratham701 » Tue, 2021-07-13 10:49 |
1 |
by Indy8976 Wed, 2022-08-24 11:27 |
|
|
Switching between hall and observer by eptv » Thu, 2019-12-05 08:49 |
1 |
by frank Thu, 2019-12-05 10:54 |
|
|
Using a AD2S1205 RTD converter by derekrose » Tue, 2023-12-12 22:36 |
1 |
by Brainiac Tue, 2023-12-26 11:56 |
|
|
Battery/Motor Current on VESC Tool is less than Actuals by gowrav » Thu, 2021-07-15 13:27 |
1 |
by skyline1970 Sat, 2021-09-18 11:44 |
|
|
Locking for reconfiguration/reprogramming This topic has been moved to "Feature Requests" (View topic) |
|||
|
How to update firmware over CAN bus by andrii619 » Wed, 2020-04-15 17:47 |
1 |
by hexakopter Sat, 2020-04-18 12:56 |
|
|
FSESC 75350 UNBALANCED_CURRENTS fault at higher loads by colmor » Thu, 2025-05-01 01:21 |
1 |
by erider Thu, 2025-10-09 07:55 |
|
|
vesc on android by TONY61 » Wed, 2025-02-05 14:00 |
1 |
by TONY61 Thu, 2025-02-06 16:08 |
|
Log in to post new content in the forum.
