You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Firmware by Phill Dixon on Mon, 2022-04-25 15:29 |
7 |
by frank Sat, 2022-04-30 14:21 |
General discussion | |
|
Poor Slow Speed Control by dcw_jubilee on Wed, 2024-02-14 13:35 |
1 |
by GiBi77930 Fri, 2024-06-14 10:34 |
General discussion | |
|
Position control of brushed dc motor with Vesc and REV through bore encoder by Greasy_D on Wed, 2023-03-29 20:17 |
14 |
by EnDeR_WiGiN Fri, 2023-04-14 17:48 |
General discussion | |
|
Dead VESC. Power up when motor is spinning. by Bor Zabric on Mon, 2018-10-08 10:16 |
4 |
by striderkent Fri, 2019-01-11 18:46 |
General discussion | |
|
Back to back BLDC motors test setup by smkulk on Tue, 2024-01-23 16:21 |
by smkulk Tue, 2024-01-23 16:23 |
General discussion | ||
|
about the encoder and gimbal by qdxiatao on Fri, 2018-01-26 16:42 |
2 |
by benjamin Fri, 2018-02-23 13:44 |
General discussion | |
|
Can you use both axes on a 2-axis nunchuck/joystick controller with VESC? by adamdorr on Tue, 2019-12-31 22:05 |
6 |
by sanketh1691 Sat, 2021-10-09 00:45 |
General discussion | |
|
IMU and ADC1/2 not working by Dwal on Wed, 2021-05-26 18:05 |
2 |
by Dwal Thu, 2021-06-03 22:34 |
General discussion | |
|
Problem with breaking in use in RC plane by fluffy on Tue, 2020-05-26 06:11 |
3 |
by fluffy Sat, 2020-05-30 03:54 |
General discussion | |
|
Can't Update Firmware by indianboy42 on Mon, 2024-06-17 08:54 |
by indianboy42 Mon, 2024-06-17 08:54 |
General discussion | ||
|
How to set a jog speed using an encoder by AK6302019 on Wed, 2019-08-07 15:42 |
by AK6302019 Wed, 2019-08-07 15:42 |
General discussion | ||
|
un-commanded reverse pulse by maxhurtz on Fri, 2022-09-02 16:01 |
5 |
by canoeman Thu, 2022-09-15 19:21 |
General discussion | |
|
base on VESC6_MkVI by gavin on Wed, 2025-06-04 15:48 |
by gavin Wed, 2025-06-04 15:48 |
General discussion | ||
|
UART CAN forwarding by frankus on Tue, 2019-01-29 16:07 |
4 |
by frankus Tue, 2021-02-16 06:35 |
General discussion | |
|
Does VESC reduce/disable regen braking based on battery voltage? by rorosaurus on Tue, 2020-08-11 23:20 |
11 |
by J_W97 Mon, 2022-03-14 14:43 |
General discussion | |
|
Torque Ramp Rate whilst in FOC by J_W97 on Mon, 2022-03-14 11:50 |
1 |
by skyline1970 Mon, 2022-03-14 20:29 |
General discussion | |
|
4.2 hw Erpm bldc mode by Katt on Wed, 2021-01-27 15:48 |
2 |
by Katt Tue, 2021-02-02 14:16 |
General discussion | |
|
Getting started with bus control of the VESC by Invert on Mon, 2018-05-21 12:04 |
3 |
by PM Thu, 2018-05-31 18:38 |
General discussion | |
|
Erratic braking on vesc using large hub motor. by jtechbop on Sun, 2021-09-19 06:54 |
2 |
by jtechbop Tue, 2021-10-19 20:59 |
General discussion | |
|
Why is the speed lower in FOC mode than BLDC mode ? by stone_1706 on Thu, 2019-01-17 08:23 |
8 |
by speed3r Wed, 2022-06-15 09:34 |
General discussion |
Pages
