You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Flipsky 75200 Pro V2.0 by sweendog311 on Fri, 2023-12-08 20:12 |
1 |
by moose09876 Thu, 2024-01-04 15:18 |
General discussion | |
|
Using the built-in gyro for RC cars by maxpla on Fri, 2020-06-26 10:49 |
1 |
by TechAUmNu Fri, 2020-06-26 16:09 |
General discussion | |
|
Motor RPM not stable FW 5.03 by TZTZ on Thu, 2021-10-21 20:51 |
1 |
by TZTZ Fri, 2021-10-22 18:45 |
General discussion | |
|
I need clarification on connecting a Magura 0-5k Ohm Pot Twist Throttle to Tronic 250 VESC. by notahorse on Fri, 2022-06-03 08:13 |
by notahorse Fri, 2022-06-03 08:13 |
General discussion | ||
|
VESC minimum RPM by askker on Thu, 2019-07-11 05:03 |
6 |
by Artius Reynolds Sun, 2020-10-18 23:25 |
General discussion | |
|
PID Speed Mode not limiting max ERPM by jordan73s on Sat, 2025-05-03 10:57 |
1 |
by colmor Thu, 2025-05-08 22:44 |
General discussion | |
|
Wheels only rotate about a quarter of a turn by Appearance on Mon, 2021-10-04 17:57 |
2 |
by drummerboy5408 Wed, 2021-10-13 05:08 |
General discussion | |
|
Battery percentage mapping by Sharkboy on Mon, 2024-05-06 22:55 |
by Sharkboy Mon, 2024-05-06 22:55 |
General discussion | ||
|
Vesc 75/300 max current by a727dd on Wed, 2020-03-04 04:34 |
by a727dd Wed, 2020-03-04 04:34 |
General discussion | ||
|
Raspberry Pi as TCP Hub/VESC Express by wittrup on Mon, 2025-04-07 10:03 |
1 |
by wittrup Mon, 2025-04-07 13:49 |
General discussion | |
|
VESC Wand shows INF and 100% Batt by BLKFLD on Sat, 2020-09-26 04:48 |
by BLKFLD Sat, 2020-09-26 04:48 |
General discussion | ||
|
Motor brake stuggling (Video) by Zanooon97 on Thu, 2023-03-09 18:57 |
2 |
by electricfox Mon, 2023-03-13 12:02 |
General discussion | |
|
20S by ahanktcd on Thu, 2024-04-25 14:51 |
by ahanktcd Thu, 2024-04-25 14:51 |
General discussion | ||
|
Motor cogs with no load, especially at high rpm by jurya on Fri, 2020-09-18 17:49 |
2 |
by jurya Fri, 2020-09-18 20:40 |
General discussion | |
|
Torque control with PWM at 10kHz for LinuxCNC + MESA + AC servo by antonchromjak on Tue, 2018-03-06 08:01 |
6 |
by Artabotak Sat, 2024-01-06 09:24 |
General discussion | |
|
Using VESC for a Linear Motor by Toshi Sharma on Wed, 2022-01-12 13:11 |
by Toshi Sharma Wed, 2022-01-12 13:11 |
General discussion | ||
|
Could not read motor configuration during detection by siegele1 on Wed, 2023-08-02 17:17 |
1 |
by electricfox Thu, 2023-08-03 08:23 |
General discussion | |
|
Cruise control by setting RPM over UART by solidgeek on Thu, 2018-02-15 10:56 |
3 |
by Lzx19961014 Thu, 2018-07-05 11:20 |
General discussion | |
|
Current control performance & best way to tune Kp and Ki by jinwonchung on Thu, 2024-10-17 15:52 |
by jinwonchung Thu, 2024-10-17 15:53 |
General discussion | ||
|
Connect both hall and incremental quadrature encoders by vpl on Tue, 2019-01-15 14:24 |
1 |
by galp Thu, 2019-01-24 14:25 |
General discussion |
Pages
