You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Noise between VESC and microcontroller by onsokumaru on Tue, 2018-04-03 21:56 |
2 |
by fourchette Tue, 2018-11-20 21:32 |
General discussion | |
Type of motors supported by VESC 6 MKIV by Sami Sahli on Thu, 2020-06-25 11:57 |
2 |
by Samuelx Tue, 2021-08-17 20:24 |
General discussion | |
Current Control issue VESC4 by yosoufe on Tue, 2018-03-20 09:28 |
5 |
by itchavenag Fri, 2019-09-13 12:06 |
General discussion | |
Wand Cruise Control, and speed control only working on Master VESC by MaddiQ on Mon, 2019-09-16 20:46 |
15 |
by hans_maier Fri, 2019-10-11 00:22 |
General discussion | |
ADC control issue by dsuresh on Fri, 2021-03-05 18:21 |
3 |
by dsuresh Wed, 2021-03-10 19:45 |
General discussion | |
Noised signal from motor NTC sensor | HW4.12 FW3.27 by ma-j-sterelektron on Wed, 2017-09-06 18:41 |
10 |
by vescsci Wed, 2020-07-15 22:47 |
General discussion | |
wand brake to reverse by michmg on Tue, 2019-09-10 23:54 |
3 |
by michmg Sat, 2019-09-14 20:16 |
General discussion | |
Controlling (HB) Braking from Arduino by Bruce on Sat, 2021-02-27 00:23 |
by Bruce Sat, 2021-02-27 00:23 |
General discussion | ||
Sudden hard acceleration at around 30 km/h. Help by kristofferbenjaminw on Tue, 2022-10-04 17:31 |
4 |
by Chris Barth Tue, 2022-10-11 20:05 |
General discussion | |
How does regenerative braking get enough voltage from my motor to charge my battery from ? by cnd on Wed, 2020-09-16 16:54 |
7 |
by flydr2 Mon, 2023-02-27 22:21 |
General discussion | |
Pid_Speed is braking despite no brake option by Flyingtux on Thu, 2022-04-07 09:41 |
2 |
by Flyingtux Thu, 2022-04-07 15:49 |
General discussion | |
FOC and very low speeds by verbeek on Mon, 2018-07-09 16:17 |
18 |
by Chris Barth Fri, 2023-11-10 04:45 |
General discussion | |
Sensored mode studering by dtmpro621 on Thu, 2023-03-02 04:40 |
by dtmpro621 Thu, 2023-03-02 05:25 |
General discussion | ||
Two Motors on same Shaft by Giga93 on Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
General discussion | |
Switching between hall and observer by eptv on Thu, 2019-12-05 08:49 |
1 |
by frank Thu, 2019-12-05 10:54 |
General discussion | |
VESC 4.12 FW5.02 CAN status messages is spamming bus, external controller, SOLVED: NEEDED INIT! by Offline on Mon, 2021-05-03 14:57 |
1 |
by Offline Tue, 2021-05-04 10:03 |
General discussion | |
Improper feedback from VESC with low speed ( BEMF ) by Pranit Bhamare on Tue, 2023-02-14 07:16 |
2 |
by Pranit Bhamare Fri, 2023-02-17 04:57 |
General discussion | |
Recommended way to implement CAN-bus communication using a Linux based controller by toma on Tue, 2019-06-11 08:32 |
8 |
by toma Thu, 2019-06-13 07:43 |
General discussion | |
Install VESC on ubuntu 18.04 bionic by rest_vesc_001 on Tue, 2020-12-08 15:34 |
by rest_vesc_001 Tue, 2020-12-08 15:34 |
General discussion | ||
Set McConf with no values --> bootloader erased? by Kakskiv on Tue, 2017-11-28 12:52 |
3 |
by basti30 Wed, 2018-08-22 22:22 |
General discussion |