You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
problem sending with setRPM(float) repeatedly at a high rate by comes04 on Thu, 2023-08-24 14:49 |
by comes04 Thu, 2023-08-24 14:49 |
General discussion | ||
|
Flipsky Mini Dual FSESC4.20+voyager remote+tankmode by allan_overbye on Fri, 2024-11-08 14:13 |
by allan_overbye Fri, 2024-11-08 14:13 |
General discussion | ||
|
(Not) Stator saturation by Stupidspencer on Sun, 2019-10-13 00:34 |
5 |
by rfedyukovich Sun, 2024-06-16 20:16 |
General discussion | |
|
Insufficient torque at low RPM by isso777 on Sat, 2022-04-23 21:13 |
10 |
by frank Tue, 2022-05-03 08:18 |
General discussion | |
|
Noised signal from motor NTC sensor | HW4.12 FW3.27 by ma-j-sterelektron on Wed, 2017-09-06 18:41 |
10 |
by vescsci Wed, 2020-07-15 22:47 |
General discussion | |
|
Autodetection values way off by thewho on Sat, 2019-05-25 20:34 |
28 |
by vadicus Mon, 2023-06-19 20:22 |
General discussion | |
|
Lehner TorQstar any experience by fabu80 on Wed, 2023-02-01 08:35 |
by fabu80 Wed, 2023-02-01 08:35 |
General discussion | ||
|
FOC and very low speeds by verbeek on Mon, 2018-07-09 16:17 |
18 |
by Chris Barth Fri, 2023-11-10 04:45 |
General discussion | |
|
Controlling a Tank by JulianT on Thu, 2020-01-23 10:06 |
2 |
by frank Thu, 2023-03-23 18:28 |
General discussion | |
|
Dual VESC, Dual UART? by kneave on Mon, 2020-08-17 22:00 |
10 |
by Duane Degn Mon, 2020-08-24 00:23 |
General discussion | |
|
SK3 Turnigy 6374 149 / encoder CUI AMT102 => can VESC 4 support position control? by fourchette on Tue, 2019-04-02 23:14 |
5 |
by pf26 Thu, 2019-04-04 11:43 |
General discussion | |
|
Calculator by kstuck on Tue, 2019-12-10 18:30 |
by kstuck Tue, 2019-12-10 18:30 |
General discussion | ||
|
Flipsky Mini FSESC 6.7 Pro Red LED flashes every two seconds by never on Sun, 2023-12-17 09:03 |
by never Sun, 2023-12-17 09:03 |
General discussion | ||
|
Advice please - VESC6 controller for a specific model aircraft application by aabill on Wed, 2019-11-27 11:31 |
5 |
by frank Sun, 2019-12-01 17:28 |
General discussion | |
|
connecting vesc tool with Prototipo by Govert on Thu, 2020-07-02 19:43 |
by Govert Thu, 2020-07-02 19:43 |
General discussion | ||
|
vesc 100250 Off-the-shelf motor by cuaxr on Mon, 2021-10-25 11:59 |
by cuaxr Mon, 2021-10-25 11:59 |
General discussion | ||
|
VESC6 success report using 250W ebike motor by thomasjfox on Mon, 2017-10-09 20:58 |
1 |
by shimdidly Tue, 2017-10-10 03:26 |
General discussion | |
|
Negative Current Spikes with Unloaded Hub Motor at Full Throttle (95% Duty) by vadicus on Wed, 2021-02-10 00:49 |
2 |
by Andreaa23 Tue, 2022-11-22 05:55 |
General discussion | |
|
Two Vesc6 MKV twin arrays ESC's - BMS CAN BUS connectivity by Spaceman on Fri, 2022-05-27 16:22 |
3 |
by Spaceman Fri, 2022-06-03 15:36 |
General discussion | |
|
Can't get motor to run using COMM port on vesc 6 MKVI and arduino mega with a potentiometer and SolidGeeks UART library by Kokonenen on Thu, 2023-03-30 11:41 |
1 |
by Kokonenen Thu, 2023-03-30 16:19 |
General discussion |
Pages
