You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
vesc6 limitations by badger1666 on Sat, 2018-04-28 19:20 |
by badger1666 Sat, 2018-04-28 19:20 |
General discussion | ||
|
How to increase the +/-165A rms current limit to 250A+ rms (350-400A peak) by ev_motors on Sat, 2018-04-28 10:18 |
by ev_motors Sat, 2018-04-28 10:18 |
General discussion | ||
|
The motor with an enkoder of AS5048 rotates unevenly by densor on Thu, 2018-04-26 11:41 |
2 |
by densor Fri, 2018-04-27 08:27 |
General discussion | |
|
Dollar signs break private messages by TechAUmNu on Tue, 2018-04-24 18:09 |
by TechAUmNu Tue, 2018-04-24 18:09 |
General discussion | ||
|
Duty vs RPM for smooth start and slow running by Davideo on Tue, 2018-04-24 14:42 |
by Davideo Tue, 2018-04-24 14:42 |
General discussion | ||
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 on Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
General discussion | |
|
Brakes completely repeatedly failing at high temperature by Paul15578 on Mon, 2018-03-26 13:06 |
10 |
by Paul15578 Sun, 2018-04-22 14:16 |
General discussion | |
|
Firmware update thru UART? by cromoly on Tue, 2018-04-17 01:19 |
4 |
by cromoly Fri, 2018-04-20 19:22 |
General discussion | |
|
can't reach the maximum speed by kingpon on Sat, 2017-10-28 04:55 |
3 |
by elektrinis Tue, 2018-04-17 21:50 |
General discussion | |
|
Extending current shunt amplifier voltage by TechAUmNu on Wed, 2018-04-11 00:43 |
2 |
by Roger Wolff Tue, 2018-04-17 08:56 |
General discussion | |
|
Hall sensor filter on VESC flier board by raess on Tue, 2018-03-27 21:00 |
17 |
by raess Wed, 2018-04-11 13:43 |
General discussion | |
|
Motor temperature increase by e-biker on Sun, 2018-04-08 20:17 |
4 |
by e-biker Mon, 2018-04-09 14:44 |
General discussion | |
|
Can't find Configurable FOC current filter in VESC TOOL by e-biker on Sun, 2018-04-08 12:18 |
2 |
by e-biker Sun, 2018-04-08 12:55 |
General discussion | |
|
Potentiometer control by khadra.m123 on Thu, 2018-04-05 08:51 |
3 |
by slapshot136 Sun, 2018-04-08 00:07 |
General discussion | |
|
acceleration speed and temp noise by badger1666 on Wed, 2018-04-04 20:18 |
5 |
by badger1666 Fri, 2018-04-06 20:13 |
General discussion | |
|
Timeout Brake Current [Fail Save] by Cuprani on Mon, 2018-04-02 00:03 |
2 |
by Cuprani Tue, 2018-04-03 12:28 |
General discussion | |
|
vesc6 help me learn by badger1666 on Sat, 2018-03-31 09:05 |
2 |
by badger1666 Mon, 2018-04-02 20:15 |
General discussion | |
|
can not start motor with high duty by qdxiatao on Sat, 2018-03-24 03:58 |
by qdxiatao Sat, 2018-03-24 03:58 |
General discussion | ||
|
Can motor parameters be detected with shaft load? by powerlabor001 on Thu, 2018-03-15 13:24 |
4 |
by powerlabor001 Sat, 2018-03-24 03:07 |
General discussion | |
|
Which encoders are supported? by raess on Thu, 2018-03-22 23:38 |
2 |
by raess Fri, 2018-03-23 22:58 |
General discussion |
Pages
