You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Flipsky 75100 e-bike ,controller gives low amperage at low rpm ,edit solved by mehmetoz1980 » Sun, 2022-11-20 17:55 |
2 |
by mehmetoz1980 Mon, 2022-11-21 13:29 |
|
|
what is HFI in the VESC? by dcameron » Sat, 2022-11-19 00:14 |
2 |
by dcameron Mon, 2022-11-21 02:07 |
|
|
Using VESC remote with non-VESC ESC by Ptkend » Tue, 2022-11-15 17:21 |
6 |
by Ptkend Sun, 2022-11-20 14:04 |
|
|
Trampa 100/250 with one old brushed DC motor....how can i change the motor spin direction????plz help!!! by Asi » Fri, 2022-11-18 12:45 |
3 |
by frank Sat, 2022-11-19 14:55 |
|
|
vesc, firmware, motor parameter calibration files? by dcameron » Fri, 2022-11-18 22:19 |
0 |
by dcameron Fri, 2022-11-18 22:19 |
|
|
status message by riku » Thu, 2022-11-17 05:31 |
1 |
by frank Thu, 2022-11-17 17:55 |
|
|
move source and header files to a folder by Jimny » Thu, 2022-11-17 05:45 |
0 |
by Jimny Thu, 2022-11-17 05:45 |
|
|
Can bus and BLDC vs FOC by Torbjorn » Fri, 2022-11-11 11:08 |
4 |
by Torbjorn Tue, 2022-11-15 14:37 |
|
|
Rion Tronic 250/ Focer3.1 using TC leads to explosion! by Drcfan » Mon, 2022-11-14 23:12 |
0 |
by Drcfan Tue, 2022-11-15 14:05 |
|
|
How to tune BLDC delay mode by Torbjorn » Tue, 2022-11-15 13:21 |
0 |
by Torbjorn Tue, 2022-11-15 13:21 |
|
|
forward, reverse, regen by ronmotor » Thu, 2022-11-10 22:37 |
2 |
by velolac Tue, 2022-11-15 12:06 |
|
|
Tuning strategy for a large motor? by MrSurly » Tue, 2022-11-01 06:51 |
1 |
by vadicus Mon, 2022-11-14 18:23 |
|
|
Am I shadowbanned? My posts never get any responses. Please respond if you see this. by MrSurly » Wed, 2022-11-02 02:02 |
2 |
by TooSlow2Care Mon, 2022-11-14 15:25 |
|
|
HFI Tuning - "Start Voltage" Question by drummerboy5408 » Sat, 2022-11-12 03:12 |
0 |
by drummerboy5408 Sat, 2022-11-12 03:12 |
|
|
Encoder Ratio for AS5047P by brian.s.stubbs@... » Fri, 2022-06-17 22:09 |
3 |
by XieMaster Fri, 2022-11-11 02:54 |
|
|
Understanding Dual VESC (dual motors) setups by Cham » Mon, 2020-09-21 18:45 |
5 |
by ronmotor Fri, 2022-11-11 01:34 |
|
|
Forum GUI by parasole » Fri, 2017-11-10 09:25 |
1 |
by VJPANDI Thu, 2022-11-10 15:07 |
|
|
Which App to use and how to wire it by philboslaggins » Sat, 2022-11-05 16:20 |
0 |
by philboslaggins Sat, 2022-11-05 16:20 |
|
|
Unable to turn on Smart Reverse by EBTEAM » Wed, 2022-11-02 08:35 |
1 |
by EBTEAM Wed, 2022-11-02 12:58 |
|
|
ADC throttle lock. by Billy_Wiz » Mon, 2022-10-31 00:57 |
1 |
by vadicus Mon, 2022-10-31 19:51 |
|
|
Encoder position resetting to 0° by Michelle90 » Tue, 2022-10-25 18:55 |
1 |
by GijsB Sun, 2022-10-30 20:17 |
|
|
Current controller issue - Glitches at low current, low RPM by GijsB » Sun, 2022-10-30 12:59 |
1 |
by GijsB Sun, 2022-10-30 15:37 |
|
|
Wow wow by st0r » Sat, 2022-05-07 21:45 |
2 |
by Hansherrman Sun, 2022-10-30 01:40 |
|
|
Inquiry about Incremental and Absolute Encoders in VESC for Robotics by sivanhere » Fri, 2022-10-28 21:02 |
0 |
by sivanhere Fri, 2022-10-28 21:02 |
|
|
Is this kogging and jitter in low rpms expected? by Snabelost » Sat, 2022-10-22 16:53 |
8 |
by Snabelost Fri, 2022-10-28 16:07 |
Log in to post new content in the forum.
