You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
How to reboot VESC from serial port by Ivko » Mon, 2021-01-04 18:44 |
0 |
by Ivko Mon, 2021-01-04 18:44 |
|
|
DUAL VESC FOR BIDIRECTIONAL ROTATION by Khaliduzzaman Mredul » Fri, 2023-05-05 06:46 |
0 |
by Khaliduzzaman Mredul Fri, 2023-05-05 11:00 |
|
|
Vesc WS2812b led issues & support by Ash » Tue, 2019-11-12 08:40 |
0 |
by Ash Tue, 2019-11-12 14:13 |
|
|
Interfacing with the VESC using UART by dhruvna » Thu, 2023-03-16 17:42 |
0 |
by dhruvna Thu, 2023-03-16 17:42 |
|
|
Can bus communication. by Piamen » Wed, 2019-11-27 06:47 |
0 |
by Piamen Wed, 2019-11-27 06:47 |
|
|
Unofficial VESC Discord server by kubark42 » Tue, 2021-11-16 16:07 |
0 |
by kubark42 Fri, 2021-11-19 03:12 |
|
|
Help Please 🥺 by Jou2023 » Sun, 2023-05-28 17:58 |
0 |
by Jou2023 Sun, 2023-05-28 17:58 |
|
|
Configuration of underwater thruster by UnderwaterMotors » Fri, 2023-03-24 18:10 |
0 |
by UnderwaterMotors Fri, 2023-03-24 18:10 |
|
|
Vesc 75100 by Matteo Christian » Wed, 2023-05-31 13:32 |
0 |
by Matteo Christian Fri, 2023-06-09 12:08 |
|
|
The rpm control is not working properly by ptss37 » Wed, 2021-11-24 03:30 |
0 |
by ptss37 Wed, 2021-11-24 03:44 |
|
|
VESC appears to loose sync when increasing throttle by srinath » Sun, 2023-06-04 04:11 |
0 |
by srinath Sun, 2023-06-04 04:11 |
|
|
DRV8302 Gate Pin output waveform is abnormal by yandongyu1998 » Fri, 2019-12-13 07:21 |
0 |
by yandongyu1998 Fri, 2019-12-13 07:21 |
|
|
No load FOC stops when full FWD throttle. by toboli » Mon, 2023-06-05 18:41 |
0 |
by toboli Mon, 2023-06-05 18:41 |
|
|
RPM and torque control modes by srinath » Fri, 2023-06-16 10:52 |
0 |
by srinath Fri, 2023-06-16 10:54 |
|
|
Error code 6 by PatWhite32 » Mon, 2023-06-19 23:15 |
0 |
by PatWhite32 Mon, 2023-06-19 23:15 |
|
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 » Wed, 2023-04-12 16:28 |
0 |
by Tom65 Wed, 2023-04-12 16:28 |
|
|
Any issues with the DRV8323? by shaman » Thu, 2019-10-24 21:50 |
0 |
by shaman Thu, 2019-10-24 21:50 |
|
|
Can someone verify this by jsbenson » Mon, 2023-06-26 09:22 |
0 |
by jsbenson Tue, 2023-06-27 07:50 |
|
|
Position Limits w/ BDC and ABI Encoder by gokulswami » Thu, 2023-04-13 10:43 |
0 |
by gokulswami Thu, 2023-04-13 10:43 |
|
|
Motors spin during detection but then won't spin by jsbenson » Tue, 2023-06-27 23:54 |
0 |
by jsbenson Tue, 2023-06-27 23:54 |
|
|
How to set up RF receiver for PPM or UART input? by adamdorr » Tue, 2020-01-07 16:23 |
0 |
by adamdorr Tue, 2020-01-07 16:23 |
|
|
Bench Testing by usaevo7 » Tue, 2023-04-25 16:50 |
0 |
by usaevo7 Tue, 2023-04-25 16:50 |
|
|
Use IMU for keeping direction by arnolde » Mon, 2024-11-25 11:12 |
0 |
by arnolde Mon, 2024-11-25 11:19 |
|
|
can not start motor with high duty by qdxiatao » Sat, 2018-03-24 03:58 |
0 |
by qdxiatao Sat, 2018-03-24 03:58 |
|
|
Storing VESC Tool data for later analysis by AidanNowa » Wed, 2024-06-12 15:57 |
0 |
by AidanNowa Wed, 2024-06-12 15:57 |
Log in to post new content in the forum.
