You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies | Last post | |
---|---|---|---|
Is there a way to use the 5 pin hall sensor with VESC? by Shivanshu Mahim » Fri, 2020-11-20 11:02 |
3 |
by Shivanshu Mahim Sat, 2020-11-21 19:34 |
|
Is there a workaround to set regen voltage, not current? by Gsorter » Sat, 2023-03-11 17:59 |
2 |
by Gsorter Sat, 2023-03-11 23:48 |
|
Is this (low-inertia) application likely to be problematic by aabill » Sat, 2019-11-23 20:54 |
2 |
by aabill Thu, 2019-11-28 14:36 |
|
Is this current reading normal? by AliBarrett10 » Sat, 2021-07-17 12:59 |
0 |
by AliBarrett10 Sat, 2021-07-17 12:59 |
|
Is this kogging and jitter in low rpms expected? by Snabelost » Sat, 2022-10-22 16:53 |
8 |
by Snabelost Fri, 2022-10-28 16:07 |
|
is VESC compatible with ROS by Knightfluffy » Fri, 2021-01-15 02:31 |
1 |
by TechAUmNu Sat, 2021-01-16 14:05 |
|
issue by control brushed DC with VESC 4.12 by segway » Sun, 2020-04-26 16:06 |
0 |
by segway Thu, 2020-06-04 10:26 |
|
Issue connecting to ESC 4.12 by Kirkness » Wed, 2020-07-08 01:40 |
2 |
by TheFallen Thu, 2020-07-09 18:01 |
|
Issue in encoder mode by limeng06217 » Tue, 2020-02-25 16:48 |
2 |
by limeng06217 Tue, 2020-02-25 16:56 |
|
Issue with my Blacktip program by abmalnaimi89 » Mon, 2023-07-31 21:00 |
0 |
by abmalnaimi89 Mon, 2023-07-31 21:00 |
|
Issue with VESC I/O on donkey car by baluja » Fri, 2022-10-28 02:56 |
0 |
by baluja Fri, 2022-10-28 02:56 |
|
Issues running a gimbal motor by ksau » Thu, 2021-03-11 16:44 |
0 |
by ksau Thu, 2021-03-11 16:44 |
|
Its dead Jim...maybe (First 6 death?) by Jacob Lord » Fri, 2017-09-22 16:50 |
11 |
by frank Thu, 2017-10-05 09:23 |
|
Jerking when changing between accelerating and braking by Phylax » Tue, 2023-01-17 11:31 |
1 |
by shokrabi Thu, 2023-02-09 23:40 |
|
Joystick Control Input by mrjoedave » Tue, 2021-03-02 02:42 |
1 |
by dsuresh Wed, 2021-03-10 19:57 |
|
Juddering on startup by ecliptalyst » Fri, 2023-10-06 00:47 |
0 |
by ecliptalyst Fri, 2023-10-06 00:47 |
|
just receaved my awesome new vesc 6 plus however it wont configurate i get an errot message. :( by sabladask » Wed, 2023-05-03 16:15 |
2 |
by frank Fri, 2023-05-05 20:54 |
|
Kill Function - Analogue Input by austrobots » Sat, 2022-12-10 12:19 |
5 |
by austrobots Tue, 2022-12-13 04:51 |
|
Kill switch by 999dom999 » Thu, 2022-04-07 10:44 |
7 |
by hnr_engineer Tue, 2022-07-26 06:07 |
|
Kill switch only stopping one motor by bmblank » Thu, 2024-01-04 22:30 |
1 |
by electricfox Sat, 2024-01-06 13:39 |
|
Knocking inside motor between 10-20km, after and before all is ok by spacewalker » Mon, 2021-05-10 11:00 |
11 |
by Fpvlee Thu, 2021-07-29 15:30 |
|
Lanyard kill switch by craig w » Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
|
large hub motors by Frankey » Sat, 2021-11-13 19:35 |
3 |
by spacewalker Tue, 2021-11-16 13:42 |
|
Lawn mower by charper » Mon, 2018-12-03 14:25 |
0 |
by charper Mon, 2018-12-03 14:25 |
|
LED HW PWM?? by milom » Fri, 2018-11-16 15:29 |
1 |
by benjamin Fri, 2018-11-23 09:57 |
Log in to post new content in the forum.