You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
More than 1A spike from the 5V 1A port of the VESC 6 HP by onluckyy » Thu, 2023-07-27 17:15 |
0 |
by onluckyy Thu, 2023-07-27 17:15 |
|
|
Ground Loop question by a.smith » Wed, 2021-06-23 13:25 |
0 |
by a.smith Wed, 2021-06-23 13:25 |
|
|
Power Switch by flyingbrike » Wed, 2021-09-08 13:47 |
0 |
by flyingbrike Wed, 2021-09-08 13:47 |
|
|
Flipsky hall sensors by alanrooks007 » Sat, 2021-06-26 00:55 |
0 |
by alanrooks007 Sat, 2021-06-26 00:55 |
|
|
Is there a way to temporarily disable kill switch by Elliott Wolbach » Mon, 2023-07-31 23:21 |
0 |
by Elliott Wolbach Mon, 2023-07-31 23:21 |
|
|
48N32P sync loss by roque.canales » Fri, 2023-08-18 11:01 |
0 |
by roque.canales Fri, 2023-08-18 11:01 |
|
|
FSESC 75350 UNBALANCED_CURRENTS fault at higher loads by colmor » Thu, 2025-05-01 01:21 |
1 |
by erider Thu, 2025-10-09 07:55 |
|
|
vesc on android by TONY61 » Wed, 2025-02-05 14:00 |
1 |
by TONY61 Thu, 2025-02-06 16:08 |
|
|
VESC with large motor by ppet36 » Sat, 2025-02-15 17:28 |
1 |
by ppet36 Sun, 2025-02-16 19:33 |
|
|
anybody interested in ninebot-segway's sensorless position observer? by lanmanck » Mon, 2020-06-01 04:33 |
1 |
by lanmanck Wed, 2020-06-03 02:57 |
|
|
How I control the RPM of my motor from VESC with Arduino? by George W. » Sat, 2020-04-25 16:10 |
1 |
by frank Thu, 2020-04-30 18:16 |
|
|
Control of 4000w bldc motor with hall effect sensors by Abdullah Ajmal » Sat, 2022-04-16 10:14 |
1 |
by frank Sat, 2022-04-16 20:01 |
|
|
Dual controller: turn left and right by coolic » Tue, 2025-02-25 13:01 |
1 |
by electricfox Thu, 2025-02-27 07:05 |
|
|
Torque Ramp Rate whilst in FOC by J_W97 » Mon, 2022-03-14 11:50 |
1 |
by skyline1970 Mon, 2022-03-14 20:29 |
|
|
PPM Configuration in VESC Tool by yourpals » Sun, 2020-06-07 21:33 |
1 |
by thefallen Mon, 2020-06-08 16:21 |
|
|
22 pole motor and potentiometer throttle by Kenneth » Mon, 2020-04-27 23:01 |
1 |
by Kenneth Tue, 2020-04-28 08:59 |
|
|
Throttle curves by Phill Dixon » Wed, 2018-05-23 18:16 |
1 |
by Tilman Baumann Thu, 2018-05-24 11:33 |
|
|
Wrong software shows up. Answered my own question. by leecon » Fri, 2025-03-07 17:50 |
1 |
by leecon Tue, 2025-03-11 17:00 |
|
|
[SOLVED] COMM_GET_VALUES on top of COMM_FORWARD_CAN not working by yes_wecangogreen » Sun, 2025-03-09 12:48 |
1 |
by yes_wecangogreen Wed, 2025-03-12 10:22 |
|
|
Vesc antispark always active by axelSSS » Wed, 2025-06-18 19:44 |
1 |
by tokerodev Fri, 2025-07-04 21:47 |
|
|
Bluetooth LE not working with Vesc Tool 3.01 by Gatze » Fri, 2022-04-22 19:31 |
1 |
by frank Thu, 2022-05-12 09:14 |
|
|
2nd Maytech 75_300 burned by Flyingtux » Wed, 2022-03-16 22:15 |
1 |
by skyline1970 Fri, 2022-03-25 19:00 |
|
|
Compiling in a different config. by Roger Wolff » Mon, 2018-09-17 17:07 |
1 |
by TechAUmNu Mon, 2018-09-17 17:12 |
|
|
VESC Error "No firmware response" by Magoroth » Tue, 2018-06-12 15:41 |
1 |
by hexakopter Wed, 2018-06-13 01:12 |
|
|
Raptor 2 by Phill Dixon » Wed, 2018-06-13 18:07 |
1 |
by frank Fri, 2018-06-22 11:35 |
Log in to post new content in the forum.
