You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter | Replies |
Last post![]() |
|
---|---|---|---|
lispBM on VESC for special algorithm by Fusion » Fri, 2024-10-25 11:34 |
4 |
by Fusion Sat, 2024-10-26 17:00 |
|
Isolated CANbus / CAN by shener » Wed, 2024-10-23 15:15 |
1 |
by Markula Thu, 2024-10-24 22:19 |
|
No sensers by Phill Dixon » Thu, 2024-10-24 18:58 |
0 |
by Phill Dixon Thu, 2024-10-24 18:58 |
|
what is this part for by ynoo443 » Wed, 2024-10-23 16:57 |
3 |
by ynoo443 Wed, 2024-10-23 17:02 |
|
How to setup my VESC with AD2S1205 by Vlahosthomas » Tue, 2024-10-22 10:33 |
0 |
by Vlahosthomas Tue, 2024-10-22 10:36 |
|
Hall Sensors Not Detected by leymane » Fri, 2023-08-18 17:12 |
4 |
by Ben26 Mon, 2024-10-21 22:45 |
|
Do All Vescs Suck? by Zeebybaby » Sun, 2024-10-20 20:33 |
0 |
by Zeebybaby Sun, 2024-10-20 20:33 |
|
Disable wrong FET temperature sensors by Flo98 » Sat, 2024-10-19 17:49 |
0 |
by Flo98 Sat, 2024-10-19 17:54 |
|
VESC setup question for a motorised rope ascender. by Ben26 » Wed, 2024-10-02 18:57 |
3 |
by Ben26 Fri, 2024-10-18 01:08 |
|
Current control performance & best way to tune Kp and Ki by jinwonchung » Thu, 2024-10-17 15:52 |
0 |
by jinwonchung Thu, 2024-10-17 15:53 |
|
Multiple VESC not working with PAS app? by radverkehr-labo... » Wed, 2024-10-16 12:57 |
1 |
by radverkehr-labo... Wed, 2024-10-16 13:36 |
|
encoder detection error by qdxiatao » Wed, 2018-05-09 12:04 |
1 |
by mona Thu, 2024-10-10 15:55 |
|
Read telemetry data from USB port by mlsc » Sun, 2024-10-06 22:01 |
0 |
by mlsc Sun, 2024-10-06 22:01 |
|
error message binding loop detected for property ! wtf by georg65 » Sat, 2024-09-28 08:49 |
0 |
by georg65 Tue, 2024-10-01 03:04 |
|
Using VESC with Ardio and PPM by gjackson » Fri, 2024-09-27 23:06 |
1 |
by electricfox Sat, 2024-09-28 08:18 |
|
rpm fail in FOC sensor mode by mansi712 » Thu, 2024-09-26 19:51 |
0 |
by mansi712 Thu, 2024-09-26 19:51 |
|
Strange controller behavior after experimenting by Deguello » Thu, 2024-09-12 07:59 |
1 |
by ricma Tue, 2024-09-24 21:55 |
|
Current mismatch between power supply and vesc tool by mansi712 » Tue, 2024-09-24 13:02 |
0 |
by mansi712 Tue, 2024-09-24 18:08 |
|
Lispscript help by mrendu43 » Mon, 2024-04-01 09:57 |
1 |
by woozie Mon, 2024-09-23 22:53 |
|
Differential steering setup by GCTech » Sat, 2020-07-04 17:38 |
4 |
by CalLangford Fri, 2024-09-20 20:29 |
|
Large robot servo controller with VESC, how to set up position control by kisdia » Thu, 2024-09-19 17:47 |
0 |
by kisdia Thu, 2024-09-19 17:47 |
|
FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 by TB_Poule » Sat, 2021-04-10 17:26 |
10 |
by Mohanangappan Wed, 2024-09-18 16:20 |
|
GPIO Pins on VESC? by phils » Sat, 2022-10-22 17:58 |
2 |
by istvan.szell@gm... Tue, 2024-09-17 12:07 |
|
Dual g-foc300 setup help!!! by Re60s » Sat, 2024-09-07 09:12 |
3 |
by Tim Read Thu, 2024-09-12 16:42 |
|
24 Volt LiFePO by Vaxinius » Tue, 2024-09-10 16:34 |
0 |
by Vaxinius Tue, 2024-09-10 16:35 |
Log in to post new content in the forum.
