You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Stop motor after certain number of rounds by Gawarmel » Wed, 2025-02-19 12:51 |
0 |
by Gawarmel Wed, 2025-02-19 12:51 |
|
|
Connecting handlebar controlls by mannberg » Thu, 2022-03-10 14:57 |
0 |
by mannberg Thu, 2022-03-10 14:57 |
|
|
issue by control brushed DC with VESC 4.12 by segway » Sun, 2020-04-26 16:06 |
0 |
by segway Thu, 2020-06-04 10:26 |
|
|
Motor seize and ERPM current ramp speed by krabsheva » Tue, 2025-05-13 06:49 |
0 |
by krabsheva Tue, 2025-05-13 07:00 |
|
|
low speed / high friction startup, max torque by schnedan » Mon, 2025-02-24 10:18 |
0 |
by schnedan Mon, 2025-02-24 10:19 |
|
|
VESC for EU pedelecs by bb67 » Mon, 2020-04-27 14:11 |
0 |
by bb67 Mon, 2020-04-27 14:13 |
|
|
Cruise control by palaga » Tue, 2025-05-20 09:20 |
0 |
by palaga Tue, 2025-05-20 09:20 |
|
|
Where can I ask technical questions about products? by MrSurly » Tue, 2022-04-19 05:22 |
0 |
by MrSurly Tue, 2022-04-19 05:22 |
|
|
Reversed polarity on one of my controllers when setting up by jsherbz92 » Sun, 2025-05-25 15:16 |
0 |
by jsherbz92 Sun, 2025-05-25 15:16 |
|
|
75200 3.3 or 5v short circuit after 10 mins of use by Vassily » Thu, 2025-02-27 23:26 |
0 |
by Vassily Thu, 2025-02-27 23:26 |
|
|
VESC is not working in ADC mode by asnamp » Wed, 2022-04-20 09:21 |
0 |
by asnamp Thu, 2022-04-21 20:11 |
|
|
Hoyt Puck Prototipo DSS50+ Firmware questions by tombell » Wed, 2020-04-29 03:56 |
0 |
by tombell Wed, 2020-04-29 03:56 |
|
|
Flipsky and Trampa getting two very different detected resistances on same motor! by colmor » Wed, 2025-05-28 22:52 |
0 |
by colmor Wed, 2025-05-28 22:52 |
|
|
Multiple VESCs on the same battery by Riccio » Wed, 2022-04-20 22:09 |
0 |
by Riccio Wed, 2022-04-20 22:09 |
|
|
CAN STATUS INTERRUPTS MOTOR OUTPUT by v1n23nt » Tue, 2022-03-15 09:06 |
0 |
by v1n23nt Tue, 2022-03-15 09:10 |
|
|
vesc tool not giving me the right values by spacemango » Tue, 2020-06-09 13:31 |
0 |
by spacemango Tue, 2020-06-09 13:42 |
|
|
VESC/FOC developer needed by CAYAGO_MS » Thu, 2020-04-30 14:23 |
0 |
by CAYAGO_MS Thu, 2020-04-30 14:23 |
|
|
base on VESC6_MkVI by gavin » Wed, 2025-06-04 15:48 |
0 |
by gavin Wed, 2025-06-04 15:48 |
|
|
How the saliency is affecting the High frequency signal injection? by SOURAV UK » Sun, 2020-05-03 11:35 |
0 |
by SOURAV UK Sun, 2020-05-03 11:35 |
|
|
Abs over current error by ogp » Sat, 2025-03-15 22:12 |
0 |
by ogp Sat, 2025-03-15 22:12 |
|
|
Recommended method for CAN Bus communication for 3 VESC by sivanhere » Sun, 2023-01-01 12:09 |
0 |
by sivanhere Sun, 2023-01-01 12:09 |
|
|
Angle offset detection by Gas_Sn4ke » Mon, 2019-01-21 07:09 |
0 |
by Gas_Sn4ke Mon, 2019-01-21 07:09 |
|
|
Separate Deadband for ADC2? by striderkent » Wed, 2019-01-23 16:31 |
0 |
by striderkent Wed, 2019-01-23 16:31 |
|
|
Problem with encoder readings with arduino by ruthvikchanda » Thu, 2018-12-06 07:06 |
0 |
by ruthvikchanda Thu, 2018-12-06 10:23 |
|
|
Any way to increase detection time? by VapeGod » Wed, 2023-01-25 05:58 |
0 |
by VapeGod Wed, 2023-01-25 05:58 |
Log in to post new content in the forum.
