You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Vesc and Arduino Interface with ppm control???? by ruthvikchanda » Mon, 2018-09-10 12:01 |
0 |
by ruthvikchanda Mon, 2018-09-10 12:01 |
|
|
FAULT_CODE_DRV Motor not spinning by Mightyorc » Sat, 2018-09-15 03:36 |
0 |
by Mightyorc Sat, 2018-09-15 03:36 |
|
|
VESC Express GPS Logging frequency by steveeng » Tue, 2025-03-25 22:55 |
0 |
by steveeng Tue, 2025-03-25 22:55 |
|
|
ADC INPUT with 4.10 HW running with 5.02 FW by mouadh » Tue, 2022-03-22 15:32 |
0 |
by mouadh Tue, 2022-03-22 17:38 |
|
|
Wolf king 11 gt 72v perimeters Help by jsherbz92 » Tue, 2025-04-01 05:52 |
0 |
by jsherbz92 Tue, 2025-04-01 05:52 |
|
|
Remote pairs but motor does not spin after VESC tool use by frunobulax » Fri, 2025-04-11 18:26 |
0 |
by frunobulax Fri, 2025-04-11 18:26 |
|
|
Flipsky 75100 + tft screen by omrishalev123 » Mon, 2024-12-30 23:10 |
0 |
by omrishalev123 Mon, 2024-12-30 23:10 |
|
|
Is BMS Tool compatible with LTO batteries? by SteveBrantley » Fri, 2025-04-18 23:12 |
0 |
by SteveBrantley Fri, 2025-04-18 23:12 |
|
|
75100 recognized as 75300 and nothing works by anaka » Mon, 2025-01-20 19:59 |
0 |
by anaka Mon, 2025-01-20 19:59 |
|
|
Help with translating/converting hall sensor values from BLDC to FOC by theviith » Thu, 2018-10-11 09:47 |
0 |
by theviith Thu, 2018-10-11 09:47 |
|
|
What is the current state of mcus support? by il_piccione » Fri, 2025-04-25 09:47 |
0 |
by il_piccione Fri, 2025-04-25 09:47 |
|
|
PPM+UART. RC and esp32 by coldreboot » Thu, 2025-01-30 23:20 |
0 |
by coldreboot Fri, 2025-01-31 15:50 |
|
|
Adjusting Acceleration Ramp with NRF & Current control by Mido » Tue, 2022-04-05 14:36 |
0 |
by Mido Tue, 2022-04-05 14:36 |
|
|
Flipsky 75200 Motor ruckelt und wird sehr schnell heiß by Oriessin » Sat, 2025-04-26 07:38 |
0 |
by Oriessin Sat, 2025-04-26 07:38 |
|
|
Best Throttle and break level by ardillolambo » Wed, 2022-03-02 18:29 |
0 |
by ardillolambo Wed, 2022-03-02 18:29 |
|
|
Payment by Paypal. by ThierryGTLTS » Wed, 2017-09-06 14:38 |
0 |
by ThierryGTLTS Wed, 2017-09-06 17:50 |
|
|
Vesc firmware to programmable Sabvoton ml60 controller. by Maciejwarloch » Tue, 2022-03-08 14:19 |
0 |
by Maciejwarloch Tue, 2022-03-08 14:19 |
|
|
Flipsky screen for Ubox driver help! by Dostawca.L » Sat, 2025-02-22 19:20 |
0 |
by Dostawca.L Sat, 2025-02-22 19:20 |
|
|
Motor compatibility (and power levels) by MrSurly » Tue, 2022-04-12 21:43 |
0 |
by MrSurly Tue, 2022-04-12 21:43 |
|
|
vesc 75100 variations for a kart build by elbracer » Mon, 2025-05-19 19:57 |
0 |
by elbracer Mon, 2025-05-19 19:57 |
|
|
Servo output CAN Formats by vinci » Mon, 2022-04-18 15:35 |
0 |
by vinci Mon, 2022-04-18 15:35 |
|
|
Updated firmware on duel hd60 now one wont turn on by Hippydeathcult » Thu, 2025-02-27 11:10 |
0 |
by Hippydeathcult Thu, 2025-02-27 11:10 |
|
|
Hub motor FOC detection. by Roger Wolff » Tue, 2018-08-21 19:12 |
0 |
by Roger Wolff Tue, 2018-08-21 19:12 |
|
|
Motor detection failed by DragosZapodeanu » Tue, 2022-04-19 15:09 |
0 |
by DragosZapodeanu Tue, 2022-04-19 15:09 |
|
|
bldc motor calibration issue by Thejesh Bollineni » Sat, 2025-03-01 00:15 |
0 |
by Thejesh Bollineni Sat, 2025-03-01 00:15 |
Log in to post new content in the forum.
