You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
Upgrading to higher voltage setup by JPK2 » Wed, 2024-06-05 22:11 |
0 |
by JPK2 Wed, 2024-06-05 22:11 |
|
|
Could use some help tuning for low speed by Berrie » Tue, 2025-07-15 20:24 |
0 |
by Berrie Tue, 2025-07-15 20:24 |
|
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset » Thu, 2022-08-04 01:44 |
0 |
by liminalsunset Thu, 2022-08-04 01:44 |
|
|
Because..why not: Full Self Riding Skateboard (autonomous skateboard) by x78163 » Wed, 2022-06-08 17:33 |
0 |
by x78163 Wed, 2022-06-08 17:33 |
|
|
Max eRPM with latest firmware by kubark42 » Fri, 2020-07-17 19:10 |
0 |
by kubark42 Fri, 2020-07-17 19:10 |
|
|
Kaabo mantis 10 elite(minimotors) FLIPSJY 75100 DUAL ALU PCB by Musik117 » Fri, 2025-07-18 14:33 |
0 |
by Musik117 Fri, 2025-07-18 14:33 |
|
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings » Fri, 2022-08-05 11:06 |
0 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
|
|
Sleep mode? by pcace » Wed, 2025-07-30 06:48 |
0 |
by pcace Wed, 2025-07-30 06:48 |
|
|
BRAND NEW R SPEC DUAL 6355 (4.12 VESC) SET UP ISSUES by rodriguezjoe1@b... » Mon, 2020-09-07 17:50 |
0 |
by rodriguezjoe1@b... Mon, 2020-09-07 17:50 |
|
|
Making master and slave motors communicate both ways by Sis7 » Tue, 2020-07-21 05:58 |
0 |
by Sis7 Tue, 2020-07-21 05:58 |
|
|
flatten the curve / powerband by TONY61 » Sun, 2025-08-10 15:26 |
0 |
by TONY61 Sun, 2025-08-10 15:26 |
|
|
Best way to run a hoverboard motor that has an AB encoder and Hall sensors, but no index? by PaulMakesThings » Thu, 2022-06-23 23:43 |
0 |
by PaulMakesThings Thu, 2022-06-23 23:43 |
|
|
VESC 60 75 IMU by Alistair Goodman » Thu, 2025-08-14 18:23 |
0 |
by Alistair Goodman Thu, 2025-08-14 18:23 |
|
|
resistance and inductance value changes when each measurement by alexshen2012 » Fri, 2022-07-01 05:42 |
0 |
by alexshen2012 Fri, 2022-07-01 05:42 |
|
|
VESC custom firmware custom UART message by steveyplst » Tue, 2020-08-04 10:23 |
0 |
by steveyplst Tue, 2020-08-04 10:23 |
|
|
Flipsky FSV 6.6 no longer working with new VESC Tool by oliver1998 » Fri, 2025-09-12 06:06 |
0 |
by oliver1998 Fri, 2025-09-12 06:06 |
|
|
Dual VESC Controller - Internal CAN Forwarding Failure -NOW WITH CODE EXAMPLE ;) by XAQ » Mon, 2025-09-15 07:52 |
0 |
by XAQ Mon, 2025-09-15 17:42 |
|
|
2 Speed ADC control by totalgeek9224 » Mon, 2025-09-22 19:47 |
0 |
by totalgeek9224 Mon, 2025-09-22 19:47 |
|
|
Dollar signs break private messages by TechAUmNu » Tue, 2018-04-24 18:09 |
0 |
by TechAUmNu Tue, 2018-04-24 18:09 |
|
|
VESC specialist required. by BlackPanthera » Mon, 2022-07-18 17:11 |
0 |
by BlackPanthera Mon, 2022-07-18 17:11 |
|
|
connecting vesc tool with Prototipo by Govert » Thu, 2020-07-02 19:43 |
0 |
by Govert Thu, 2020-07-02 19:43 |
|
|
How do you turn on traction control ( I can't remember) by msim2 » Fri, 2022-05-20 22:06 |
0 |
by msim2 Fri, 2022-05-20 22:06 |
|
|
VESC 6 Mark III and Traxxas Summit Radio Receiver PWM / PPM Signals by j98221@gmail.com » Fri, 2020-07-03 07:27 |
0 |
by j98221@gmail.com Fri, 2020-07-03 07:27 |
|
|
Problem with Android app by Er-Chispa » Wed, 2025-10-08 20:58 |
0 |
by Er-Chispa Wed, 2025-10-08 21:02 |
|
|
How to increase the +/-165A rms current limit to 250A+ rms (350-400A peak) by ev_motors » Sat, 2018-04-28 10:18 |
0 |
by ev_motors Sat, 2018-04-28 10:18 |
Log in to post new content in the forum.
