You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
No, BLDC is not dead. by Pimousse » Wed, 2019-06-12 17:41 |
5 |
by hexakopter Sat, 2020-04-18 12:30 |
|
|
VESC help offered for private persons and companies by electricfox » Thu, 2023-10-05 17:41 |
5 |
by Jetboard5 Sat, 2025-03-22 20:24 |
|
|
AC Synchronous motor support by Dark » Mon, 2019-07-29 15:03 |
5 |
by rizanirusli Wed, 2021-05-05 08:39 |
|
|
Cant connect to Flipsky 75100 by Ed222 » Sun, 2022-03-20 00:31 |
5 |
by wimleo Wed, 2025-03-19 17:51 |
|
|
trampa by badger1666 » Mon, 2017-12-11 22:37 |
5 |
by wdaehn Wed, 2017-12-13 12:17 |
|
|
Sudden kick (from motor current cut off?) by darowi » Mon, 2017-10-02 18:56 |
5 |
by darowi Tue, 2020-09-15 12:45 |
|
|
Two Motors on same Shaft by Giga93 » Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
|
|
Cannot downgrade from 5.03 to 5.02 by kallep » Sat, 2022-02-26 19:08 |
5 |
by frank Sat, 2022-03-12 12:09 |
|
|
Hall sensor table by spacemango » Tue, 2020-06-16 15:47 |
5 |
by pf26 Tue, 2020-06-23 15:10 |
|
|
Emergency Stop SSR - Blowing up Microcontroller by J_W97 » Tue, 2022-03-01 14:46 |
5 |
by frank Tue, 2022-03-01 20:19 |
|
|
VESC configuration with a high KV Motor by batdan » Sat, 2018-01-13 23:01 |
5 |
by Roger Wolff Sun, 2018-02-04 10:09 |
|
|
a motor for VESC !! by themotorman » Sat, 2018-12-29 06:19 |
5 |
by TechAUmNu Fri, 2019-11-15 14:20 |
|
|
Independent Throttle on ADC1 and Brake on ADC2? by striderkent » Tue, 2019-01-08 18:31 |
5 |
by canarispott Sun, 2021-10-31 02:44 |
|
|
What is the best way to make an emergency button to stop the motor from spinning? by kdomanski » Sat, 2021-01-30 14:18 |
5 |
by skyline1970 Mon, 2021-02-01 21:25 |
|
|
VESC - custom board by st0r » Wed, 2023-03-08 12:21 |
5 |
by st0r Sat, 2023-04-01 01:51 |
|
|
Dual brushed motors from 1 R/C stick? by VESC1 » Thu, 2019-01-31 06:19 |
5 |
by sam.vanratt Sun, 2019-02-03 16:30 |
|
|
Kill Function - Analogue Input by austrobots » Sat, 2022-12-10 12:19 |
5 |
by austrobots Tue, 2022-12-13 04:51 |
|
|
Motor Controller Recommendations - 84V max - 50A Continuous by dylanu » Thu, 2021-11-11 22:54 |
5 |
by mikael Sat, 2023-09-30 01:46 |
|
|
RL test fails by de-bodgery » Wed, 2021-09-29 19:55 |
5 |
by TechAUmNu Tue, 2021-10-26 01:22 |
|
|
missing Analog Throttle failsafe by bosko » Thu, 2019-12-05 16:47 |
5 |
by bosko Fri, 2019-12-06 13:25 |
|
|
Help calibrating a hub motor by Tin_Man_0 » Thu, 2019-12-26 01:17 |
5 |
by vadicus Tue, 2020-01-07 00:48 |
|
|
Pulling fault codes without USB by shaman » Fri, 2019-10-18 15:13 |
5 |
by shaman Sun, 2019-10-20 22:54 |
|
|
ADC Throttle Voltage Issue by Reichen Schaller » Fri, 2022-05-20 01:02 |
5 |
by Gatze Wed, 2022-05-25 17:10 |
|
|
Range not showing accurately by th3jonathan » Tue, 2022-05-24 17:43 |
5 |
by frank Mon, 2022-05-30 07:53 |
|
|
Website updates by benjamin » Fri, 2018-02-23 17:45 |
5 |
by benjamin Wed, 2018-03-14 10:46 |
Log in to post new content in the forum.
