You are here
General discussion
Log in to post new content in the forum.
Topic / Topic starter |
Replies | Last post | |
|---|---|---|---|
|
customer app for pwm input by ccrbs » Tue, 2020-08-11 12:06 |
0 |
by ccrbs Tue, 2020-08-11 12:06 |
|
|
Cut off after reaching Max. Duty Cycle by toboli » Thu, 2023-06-01 22:54 |
2 |
by toboli Sat, 2023-07-01 13:32 |
|
|
Cut-out at >40A by thewho » Thu, 2018-09-13 20:24 |
0 |
by thewho Thu, 2018-09-13 20:24 |
|
|
Dangerous bug when using KILLSWITCH and PPM, FW5.03 by corgon » Wed, 2022-12-14 16:37 |
2 |
by corgon Thu, 2022-12-15 23:10 |
|
|
DC-Link Capacitor Selection by rushi95 » Sat, 2019-05-18 12:15 |
1 |
by hexakopter Sat, 2019-05-18 12:39 |
|
|
Dead VESC. Power up when motor is spinning. by Bor Zabric » Mon, 2018-10-08 10:16 |
4 |
by striderkent Fri, 2019-01-11 18:46 |
|
|
Delayed start for slave motor by rsknudsen-dk » Mon, 2020-04-06 10:06 |
0 |
by rsknudsen-dk Mon, 2020-04-06 10:06 |
|
|
Delayed Startup with ADC Throttle by Marctwo » Sat, 2020-07-04 21:48 |
11 |
by pwd Wed, 2024-05-29 16:12 |
|
|
DELETE THREAD by Donnyten » Tue, 2024-12-10 05:37 |
0 |
by Donnyten Sun, 2024-12-29 00:56 |
|
|
Design custom VESC 6 Hardware by brightlightbeam » Sat, 2020-07-04 14:18 |
5 |
by Gatze Mon, 2022-04-18 18:22 |
|
|
Designing a robust power stage using Mosfets by ripperpc » Tue, 2020-05-05 08:04 |
0 |
by ripperpc Tue, 2020-05-05 08:04 |
|
|
Detection failed by Jetboard5 » Sat, 2025-03-22 01:28 |
3 |
by Jetboard5 Sat, 2025-03-22 20:29 |
|
|
Device shutting down by gjos » Sun, 2024-04-21 22:23 |
0 |
by gjos Sun, 2024-04-21 22:23 |
|
|
Did I damage My Vesc? by Kent Church » Tue, 2022-01-11 04:47 |
1 |
by skyline1970 Wed, 2022-01-19 09:46 |
|
|
Difference between Brake Current, Full Brake etc by wdaehn » Wed, 2018-02-21 15:32 |
4 |
by rodread Sat, 2018-03-03 10:45 |
|
|
Difference between ERPM and Duty Cycle by dormanae » Wed, 2022-02-23 17:21 |
1 |
by j.konrad Thu, 2022-02-24 02:08 |
|
|
Difference between maximum current values by Rico » Fri, 2019-06-14 16:06 |
1 |
by frank Sat, 2019-06-15 12:21 |
|
|
Difference between the current, duty cycle and PID speed control mode by tromes » Thu, 2020-06-11 07:51 |
8 |
by Onarb Kabr Wed, 2025-01-15 13:32 |
|
|
difference between VSEC GOLD, Silver, Bronze by roeebloch » Sun, 2021-04-18 19:43 |
2 |
by frank Wed, 2021-05-26 11:04 |
|
|
Differential steering setup by GCTech » Sat, 2020-07-04 17:38 |
4 |
by CalLangford Fri, 2024-09-20 20:29 |
|
|
Difficulty Tuning HFI on Hoverboard Motor for Low-Speed, High-Torque Application by Ponps33 » Tue, 2024-11-19 10:29 |
0 |
by Ponps33 Tue, 2024-11-19 10:29 |
|
|
Direct drive wheel ac servo+vesc by adilrepas » Wed, 2021-05-26 12:50 |
0 |
by adilrepas Wed, 2021-05-26 12:58 |
|
|
Disable Regen braking below set erpm by HighV3locity » Thu, 2024-03-28 18:23 |
1 |
by flez1966 Thu, 2024-04-11 15:02 |
|
|
Disable throttle while braking by rl_19 » Sat, 2022-03-19 00:05 |
7 |
by flez1966 Thu, 2024-03-21 09:41 |
|
|
Disable wrong FET temperature sensors by Flo98 » Sat, 2024-10-19 17:49 |
0 |
by Flo98 Sat, 2024-10-19 17:54 |
Log in to post new content in the forum.
