You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter |
Replies |
Last post | |
|---|---|---|---|
|
One motor runs fine, other one doesn't by Spamantha » Sun, 2021-09-12 17:00 |
3 |
by Spamantha Sun, 2021-09-26 12:03 |
|
|
Custom application and UART by Dennis Freiburg » Sat, 2020-01-11 13:19 |
3 |
by Dennis Freiburg Sun, 2020-01-12 19:37 |
|
|
VESC 4.20 Schematic by evbkez » Fri, 2019-09-20 07:59 |
3 |
by TheFallen Fri, 2019-09-27 17:45 |
|
|
PyVESC - Realtime Data - Experiment Export .csv file by Eric_IraLo » Wed, 2024-03-13 20:03 |
3 |
by Eric_IraLo Thu, 2024-03-14 20:14 |
|
|
large hub motors by Frankey » Sat, 2021-11-13 19:35 |
3 |
by spacewalker Tue, 2021-11-16 13:42 |
|
|
Wand (and app) not pairing by Jonny254 » Mon, 2019-10-07 15:17 |
3 |
by Daada Wed, 2022-04-27 10:58 |
|
|
HELP! Underpowered motor! by natebakesacake123 » Thu, 2024-02-08 04:22 |
3 |
by natebakesacake123 Thu, 2024-02-08 21:22 |
|
|
75/300 connection issues FW3.6 by renaudbarbier » Fri, 2019-11-01 20:17 |
3 |
by frank Tue, 2019-11-05 09:18 |
|
|
Set McConf with no values --> bootloader erased? by Kakskiv » Tue, 2017-11-28 12:52 |
3 |
by basti30 Wed, 2018-08-22 22:22 |
|
|
Open source hardware? by Jens » Thu, 2017-09-14 18:15 |
3 |
by frank Fri, 2017-09-15 14:01 |
|
|
Optimizing VESC6 setup for my Giant Lego Go-Kart project by mantisrobot » Thu, 2020-06-18 13:29 |
3 |
by TechAUmNu Mon, 2020-06-29 10:19 |
|
|
Two Vesc6 MKV twin arrays ESC's - BMS CAN BUS connectivity by Spaceman » Fri, 2022-05-27 16:22 |
3 |
by Spaceman Fri, 2022-06-03 15:36 |
|
|
HArd power off switch by jakaranda » Mon, 2018-10-29 11:15 |
3 |
by sam.vanratt Sat, 2018-11-24 18:08 |
|
|
Controlling general BLDC motors by sinned6915 » Wed, 2020-08-19 01:56 |
3 |
by TheFallen Sun, 2020-08-23 16:51 |
|
|
where to source BLDC 6.5in geared wheel? by fourchette » Thu, 2018-11-08 00:05 |
3 |
by fourchette Mon, 2018-11-19 22:54 |
|
|
Flux linkage detection failed by Count1310 » Sat, 2020-08-22 16:30 |
3 |
by drummerboy5408 Wed, 2022-04-13 07:42 |
|
|
Ideal Thermistor/Temperature Sensor? by josh » Sat, 2017-10-14 07:07 |
3 |
by josh Sun, 2017-10-22 06:52 |
|
|
Cant get Rotor position to work by nancio » Mon, 2022-06-06 20:47 |
3 |
by frank Thu, 2022-06-09 09:05 |
|
|
VESC acceleration control on setRPM by fourchette » Tue, 2019-01-08 12:02 |
3 |
by fourchette Wed, 2019-01-09 10:38 |
|
|
Wiring a touchscreen to a vesc by posthy » Tue, 2022-06-14 10:22 |
3 |
by frank Thu, 2022-06-16 08:35 |
|
|
when speed of vesc motor too fast and the arduino pin signal is unstable by HumorLogic » Tue, 2021-04-06 14:21 |
3 |
by woliam Sat, 2021-04-10 15:17 |
|
|
Able to read CAN messages from VESC but cannot write messages to CAN Bus. by willd3543 » Wed, 2023-04-05 23:49 |
3 |
by benjamin Wed, 2023-04-12 07:32 |
|
|
VESC 6+ CAN bus continued by kimpet » Fri, 2019-04-26 13:27 |
3 |
by Tinkerer Fri, 2021-04-02 06:31 |
|
|
100k NTC by CTSchorsch » Tue, 2019-05-07 17:18 |
3 |
by Roger Wolff Sat, 2019-05-11 13:00 |
|
|
Where to connect the Button for Reverse driver?, in ADC mode (Ebike throttle) by Astropower » Sun, 2019-05-19 22:10 |
3 |
by hackish Sun, 2019-09-08 05:31 |
Log in to post new content in the forum.
